You are browsing camaro6 
12-08-2018, 08:05 PM
|
#57 |
 Drives: 2018 1LS 1LE Join Date: Jun 2017
Location: Massachusetts
Posts: 162
|
Thanks for the DIY. Installed today.
Couple notes: 1. Fishing the harness through to the passenger side took longer then it should have. Need coat hanger or similar. And fish right above the knee pads - not back towards the firewall. 2. The glue that holds down the door seal is pretty sticky - have to be careful not to touch. 3. If planning to install sill protective film - do it before installing.
__________________
2018 Garnet Red 1LS 1LE V6 w/Tech
1100 - 07/26/2017 | 4300 - 09/15/2017 at rail yard 3000 - 08/16/2017 | 4200 - 09/18/2017 shipped! 3100 - 08/19/2017 TPW 09/11/2017 | 4800 - 09/20/2017 train journey done 3400 - 08/25/2017 | 5000 - 09/22/2017 at the dealer, and picked up! 4300 - 09/12/2017 Built! VIN available 4B00 - 09/14/2017 move to rail yard |
|
|
|
01-19-2019, 05:41 AM
|
#58 |
  
Drives: 2016 Hyper Blue Metallic 1SS M6 NPP Join Date: Jan 2016
Location: Indiana
Posts: 891
|
Glad people are finding this helpful and installing their new illuminated sill plates. Enjoy
__________________
2016 Hyper Blue Metallic 1SS M6 with body color hood vents, Silver broken 5 spoke wheels, NPP dual exhaust, Dark Night Interior Spectrum Lighting, Illuminated door sills plates. Upgrades include: Roto-Fab intake, Mishimoto catch can, MBRP cat-back Race exhaust, TSP 1 7/8 headers, EFI E85 Flex Fuel, MRR M017 graphite wheels with Nitto N555 G2 tires, Goodridge stainless steel brake lines, Powder coated Brembo calipers, BMR suspension, Eibach sport springs, Emblempros fender badges Order ID: TDHQMS 1100 on 01/07/2016 at Penske Chevrolet 6000 on 02/23/2016 Delivered to customer |
|
|
|
|
04-26-2020, 12:23 AM
|
#59 |
 
Drives: 2019 1SS M6 Join Date: Feb 2020
Location: Harrisburg,Pa.
Posts: 74
|
I just finished up the sill plate install...A straight forward procedure with all the tips in this thread... Thanks to everyone who contributed..
 There was plenty of length to the factory wire harness and I sent it through the console area near the knee pads as suggested..Only took about 1 minute to get it through there with a 2ft section of hard copper wire as the fish... And you were correct,the door seal's hog snot is a mess and strung out quite a bit..I didn't want that getting on anything in there.. |
|
|
|
|
04-26-2020, 02:24 AM
|
#60 |
 Drives: 2020 Chevrolet Camaro Coupe 2SS 1LE Join Date: Feb 2020
Location: Nevada
Posts: 296
|
Nice job. 👍
|
|
|
|
|
05-11-2021, 04:14 PM
|
#61 | |
Drives: Summit White V6 M6 NPP Join Date: Feb 2017
Location: Toronto
Posts: 52
|
Quote:
|
|
|
|
|
|
12-03-2022, 03:02 PM
|
#62 |
 Drives: 2022 2SS 1LE Join Date: Nov 2021
Location: WNY
Posts: 10
|
Sorry for the dumb question but, after you cut the gray wire, do you have to strip the ends? I don’t know what the “recommended service technique” is. Can I just plug in the clipped ends and crimp?
Thanks
__________________
2022 1SS 1LE Riverside Blue
|
|
|
|
|
|
|
|
|
Post Reply
|
| Thread Tools | |
|
|
