02-14-2021, 12:32 PM | #15 | |
Drives: Wild Cherry LT1 Join Date: Dec 2016
Location: Massachusetts
Posts: 1,925
|
Quote:
I may want to give it a shot too. |
|
02-14-2021, 08:56 PM | #16 |
Drives: 2019 2SS Camaro Join Date: Apr 2012
Location: Al
Posts: 828
|
|
02-14-2021, 09:07 PM | #17 |
Drives: Wild Cherry LT1 Join Date: Dec 2016
Location: Massachusetts
Posts: 1,925
|
Ah, ok... no problem. I’ll figure it out.
|
02-19-2021, 02:48 PM | #18 |
Drives: 2019 2SS Camaro Join Date: Apr 2012
Location: Al
Posts: 828
|
So I have part numbers of 23390130 and for the other side 23390131 about 60 bucks each. I think it really helps
|
02-19-2021, 05:55 PM | #19 |
Drives: '17 2SS convertible'20 Yukon Denali Join Date: Nov 2011
Location: Cedar Park, Texas
Posts: 2,934
|
What part of the car are those pieces put? I can't tell from the small drawing. GM parts direct has them for $57 left side and $59 right.
__________________
Richard
2017 2SS SIM convertible, A8, NPP, MRC, 56R wheels, GM CAI, Diode Dynamics Side Markers Delivered: 08/15/2016 #TeamBeckyD |
02-19-2021, 06:13 PM | #20 |
Drives: Wild Cherry LT1 Join Date: Dec 2016
Location: Massachusetts
Posts: 1,925
|
|
02-19-2021, 10:27 PM | #21 |
Drives: 2019 2SS Camaro Join Date: Apr 2012
Location: Al
Posts: 828
|
They are supposed to be the gray peices that go underneath the car right and left. Its like a gray carpet cardboard type stuff. it is exposed to the weather. U will need some nuts to bolt it on. The studs are there. Up front their are a couple clips that slide into the frame and then a 10 mil headed bolt goes into. This is starded on the ss coupe but for some reason no on the vert.
|
03-21-2021, 05:58 PM | #22 | |
Drives: Camaro SS 2018 Convertible Join Date: Apr 2019
Location: Switzerland
Posts: 116
|
Quote:
Do you have some pictures to see how it looks and where you had to cut? Thank you |
|
03-21-2021, 06:52 PM | #23 |
Drives: 2019 2SS Camaro Join Date: Apr 2012
Location: Al
Posts: 828
|
like a inch sq on the edge where the bolt goes on the frame. no big deal at all. just do it and you will see. need the nuts and 2 bolts on the front with the clip. per side like the fender liners have
|
05-13-2021, 08:45 AM | #24 |
Drives: Camaro SS 2018 Convertible Join Date: Apr 2019
Location: Switzerland
Posts: 116
|
Do you know the torque of the bolts to be used on the x arms under the car?
Thank you |
05-13-2021, 10:00 AM | #25 |
Thank you Al Oppenheiser!
Drives: Red Hot A10 ZL1 Convertible Join Date: Jun 2017
Location: Sarasota, FL
Posts: 4,975
|
43 ft-lbs for both the main X-brace and rear X-brace.
|
05-14-2021, 02:03 PM | #26 |
Drives: Camaro SS 2018 Convertible Join Date: Apr 2019
Location: Switzerland
Posts: 116
|
|
05-14-2021, 04:30 PM | #27 |
Drives: 2019 2SS Camaro Join Date: Apr 2012
Location: Al
Posts: 828
|
I dont know if its relevant but you do not have to touch the bolts on the braces to put on the cading
|
05-17-2021, 03:59 AM | #28 |
Drives: Camaro SS 2018 Convertible Join Date: Apr 2019
Location: Switzerland
Posts: 116
|
Does someone have the part number of the nuts which goes on the studs?
|
|
|
Post Reply
|
|
|