04-16-2021, 11:20 PM | #1 |
Drives: 2017 Camaro 1LT RS Join Date: Apr 2021
Location: California
Posts: 5
|
RS emblem position measurements
Can some one please give me the position measurements of the rear bumper RS emblem (6 gen Rs) would really appreciate it!
|
04-16-2021, 11:46 PM | #2 |
Drives: 2018 Camaro V6/RS Join Date: Nov 2018
Location: MI
Posts: 1,596
|
Not sure if there is an exact placement to be honest since I've seen it vary in many cases
|
04-17-2021, 10:32 AM | #3 |
Drives: 2017 Camaro 1LT RS Join Date: Apr 2021
Location: California
Posts: 5
|
What I know that it’s centered to the left exhaust tip , the measurement I need is the one from the top line where the bumper starts to bend to the top of the letters.
|
04-17-2021, 10:41 AM | #4 |
Drives: 2018 Camaro V6/RS Join Date: Nov 2018
Location: MI
Posts: 1,596
|
I can measure mine if you like, but like I said I've seen it vary from the factory for whatever it's worth. I first noticed this variation when getting my oil changed at the dealership. From the RS to the SS I saw definite differences in the placement of the emblem
|
04-17-2021, 02:04 PM | #5 |
Drives: 2016 1LT RS Convertible Join Date: Apr 2013
Location: Boston
Posts: 85
|
I would say about 2 5/8 + a little. Here is a picture.
|
04-17-2021, 02:19 PM | #6 |
Drives: 2018 Camaro V6/RS Join Date: Nov 2018
Location: MI
Posts: 1,596
|
Mine is 3.5 inches
|
04-17-2021, 02:54 PM | #7 |
Drives: 2017 Camaro 1LT RS Join Date: Apr 2021
Location: California
Posts: 5
|
So I guess it varies!
|
04-17-2021, 02:56 PM | #8 |
Drives: 2018 Camaro V6/RS Join Date: Nov 2018
Location: MI
Posts: 1,596
|
Yes it definitely varies. I don't think it's a lot in general, but enough to notice it sometimes
|
04-18-2021, 02:09 PM | #9 |
Drives: 2017 Camaro 1LT RS Join Date: Apr 2021
Location: California
Posts: 5
|
What I figured out that 2016 Rs models are higher positioned than 2017 and 2018
|
04-18-2021, 02:31 PM | #10 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,616
|
It'd be surprising if the factory didn't have a placement tool, I know they do have one for the bowtie on the trunk lid.
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
04-18-2021, 02:56 PM | #11 |
Drives: 2017 Camaro 1LT RS Join Date: Apr 2021
Location: California
Posts: 5
|
They don’t I’ve tried everywhere
|
|
|
Post Reply
|
|
|