07-24-2020, 12:05 PM | #1 |
Drives: 2019 Camaro 2SS 1LE Join Date: Apr 2020
Location: San Jose, CA
Posts: 3
|
Replacing brake fluid
Hi forum! Noob question here:
I'm replacing the brake fluid on my 4,000 mile old car for some high temp fluid. With the "old" fluid being relatively new, I don't expect it to be discolored. How can I tell it's been flushed out and I'm getting new fluid on the bleed screw? |
07-24-2020, 02:01 PM | #2 |
Drives: 2016 Camaro 1LT Join Date: Jan 2016
Location: California
Posts: 3,491
|
Without a color difference, you really can't simply by bleeding without letting it drain and get air in the system using a vacuum/pressure system.
if you want to get ocd about it, you'll need a tool that can activate the ABS modules to get the fluid out of them as well as simple bleeding wont purge them. any other solution is probably just guestimating how much each line to wheel can carry and filling and bleeding that amount. But you'd still need to play with the abs module to clean it out too. |
07-24-2020, 02:19 PM | #3 |
Drives: '19 ZLE, S54 E36M3 Join Date: Feb 2018
Location: North Augusta, SC
Posts: 227
|
My method. YMMV.
I used a syringe to suck as much old fluid out of the reservoir as I could without uncovering the ports. It took almost 1/2 liter to refill it. I then bled about 1/4 liter from the first bleed screw in back to purge the long line, then did about 10 pedal pumps on each bleed screw after that with the pressure bleeder attached. Total volume about 1.5 L. On subsequent bleeds using the same fluid usually use 1 L as I don’t drain the reservoir. I push a liter through the system before each track event. Perhaps overkill, but after 30 years on track, I’m not changing up my game now. I also use a syringe with a tiny hose (helps to have a vascular surgeon friend..) to remove the residual fluid from the bleeder screws so it doesn’t weep out when it gets hot. |
07-24-2020, 06:31 PM | #4 |
Drives: 2019 Camaro 2SS 1LE Join Date: Apr 2020
Location: San Jose, CA
Posts: 3
|
Thanks guys! I'll go with m3bs method, and hopefully there's a bit of a color difference even though the car is not that old.
|
07-26-2020, 04:19 PM | #5 |
Drives: 2019 Camaro 2SS Join Date: Nov 2019
Location: Connecticut
Posts: 135
|
There wont be a color difference. Drain 250cc out of the rears, and 150cc out of the fronts. That's what I did.
__________________
2019 Camaro 2SS, Shadow Grey
|
07-26-2020, 06:01 PM | #6 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,675
|
After you add new fluid to the reservoir at the beginning of the procedure, pump the clutch 200 times.
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
07-28-2020, 01:35 PM | #7 | |
TEXIT
Drives: 2019 ZL1 M6 Join Date: Aug 2018
Location: Republic of Texas
Posts: 160
|
Quote:
Last edited by getchapull; 07-28-2020 at 02:00 PM. |
|
|
|
Post Reply
|
|
|