Need some transmission help

Conner0388 · 11-29-2023, 09:17 PM

Is there anybody here familiar with the tr6060 that comes on the 2016 camaro ss. I pulled the bellhousing off not knowing it was a integregated bellhousing. I put it on and the something just isn’t right. The shifter is sloppy and probably not even in the right gear. I’m clueless here

*radz28* · 11-30-2023, 07:07 AM

Could you be pinching any wires or the clutch slave line or vent lines anywhere? Are you sure you aligned the input shaft into the pilot bearing correctly? It could be a whole lot...

Conner0388 · 11-30-2023, 07:52 PM

Quote:

Originally Posted by radz28

Could you be pinching any wires or the clutch slave line or vent lines anywhere? Are you sure you aligned the input shaft into the pilot bearing correctly? It could be a whole lot...

The engine is still out of the car. I’m just putting the bellhousing back on to the transmission itself. I’m able to get it on but the problem I’m having now is that the shifter feels good but won’t go into neutral or 4th gear so now I’m at a lost.

cjperformance · 12-01-2023, 06:56 AM

A guess here, but it may require some rotation of the input shaft to allow the gears and synchros to become more aligned. I can think of cases in my past where i tried to row gears on a non running car and certain gears were blocked. Once the input shaft rotates by starting the car, the gears/synchros would align better and mesh.

No clue if this is the case, just throwing out a wild guess. I could see this happening if you get perfect MIS-alignment of the synchros.

dpevans · 12-02-2023, 03:39 PM

Did you make sure the trans and shifter were in neutral before putting it back on. Do a google search on how to install a shifter on the Tremec 6060 there is a specific order on how to install. I don't see the bell housing having anything to do with the shifter working properly.

11-29-2023, 09:17 PM	#1
Conner0388 Drives: 2016 Chevy Camaro 2SS Join Date: Sep 2020 Location: Flagler beach, Florida Posts: 214 View My Garage	Need some transmission help Is there anybody here familiar with the tr6060 that comes on the 2016 camaro ss. I pulled the bellhousing off not knowing it was a integregated bellhousing. I put it on and the something just isn’t right. The shifter is sloppy and probably not even in the right gear. I’m clueless here

11-30-2023, 07:07 AM	#2
radz28 Petro-sexual Drives: Ultra-Grin Join Date: Oct 2006 Location: Crazy Coast Posts: 15,201 View My Garage	Could you be pinching any wires or the clutch slave line or vent lines anywhere? Are you sure you aligned the input shaft into the pilot bearing correctly? It could be a whole lot... __________________ '20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs

12-01-2023, 06:56 AM	#4
cjperformance Drives: 2017 Camaro SS 50th Anniversary Join Date: Apr 2021 Location: Missouri Posts: 929	A guess here, but it may require some rotation of the input shaft to allow the gears and synchros to become more aligned. I can think of cases in my past where i tried to row gears on a non running car and certain gears were blocked. Once the input shaft rotates by starting the car, the gears/synchros would align better and mesh. No clue if this is the case, just throwing out a wild guess. I could see this happening if you get perfect MIS-alignment of the synchros. __________________ 2017 50th Anniversary Edition \| P1X Stage 2 DSX Aux Low Side \| LT4 high side \| Flex Fuel TooHighPsi Port Injection (installed & tuning) CircleD 3K Stall \| QA1 CF Driveshaft Forgestar F14 Drag 17x10 NT555R2 305/45/17 Rear Forgestar F14 18x8 NT555G2 235/50/18 Front 10.84@131 w/4.13" pulley ??.??@??? w/3.7" pulley (installed & tuning)

12-02-2023, 03:39 PM	#5
dpevans Drives: 2024 Riverside Blue 2SS 1LE Join Date: Mar 2016 Location: Fort Wayne, IN Posts: 1,208	Did you make sure the trans and shifter were in neutral before putting it back on. Do a google search on how to install a shifter on the Tremec 6060 there is a specific order on how to install. I don't see the bell housing having anything to do with the shifter working properly.

User Name		Remember Me?
Password