Drink Cup Holder Insert - Page 4 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Wyld Irish · 09-30-2009, 06:47 PM

It's probably a bit late for this ... and your going to think I'm crazy.

But get a 2 x 2 square of black felt. Cut it to match the insert plate. Then glue it (felt side up) to the bottom of the plate. Press it really hard (a press if you have one ... some really heavy books if you don't) while it drys.

Your trying to get just a little edge (very little edge) of the felt to stick out from the insert plate edges. This will help cover that metal to plastic rough edge look.

and should only run you about 4 bucks...

dragonZ28 · 09-30-2009, 06:53 PM

In our product's defense, those pictures make the part look scratched up and really somewhat misrepresent the insert. There is debris and fingerprints all over that piece.

Here is what the item looks like in our photo in our car:

A picture can make something look bad when it really isn't. Please don't rush to judgement from photos. It is a quality product.

Wyld Irish · 09-30-2009, 07:10 PM

I hope I didn't make it sound like I was bagging on your insert. The insert is great .. good lines on the metal and the cuts are nice a crisp .. no spurs .. totally top notch.

I was just tossing out a way to camouflage where the metal and plastic meet. For those who are looking for something like that.

Mod4SS · 09-30-2009, 07:14 PM

Quote:

Originally Posted by n-shane@hotmail.com

seriously paid 50 bucks for that? wow. LOL

Quote:

Originally Posted by ralyrat

http://cgi.ebay.com/ebaymotors/2010-...Q5fAccessories

Better than paying $117.00 on Ebay

... $50 is nothing if the cosmetic mod is right. I was the guinea pig, so you should be thanking me...

dragonZ28 · 09-30-2009, 07:23 PM

The picture we took above in our post was a very clean car, a very cleaned up part, "the way it should be" taken with plenty of light etc.....
You guys can use your own judgement. I also have more pictures if needed.

Thanks, Roger

Mod4SS · 09-30-2009, 07:25 PM

Quote:

Originally Posted by dragonZ28

In our product's defense, those pictures make the part look scratched up and really somewhat misrepresent the insert. There is debris and fingerprints all over that piece.

The product is quality, for sure... just needs some refining. There are a few fingerprints on it and a little debris in the cupholder, but I wanted to give it a realistic look. I zoomed in on it, so people could see an untouched photo. This is a good idea and will sell plenty if it can be refined properly. IMO, the middle of the insert should be semi open instead of connected.

dragonZ28 · 09-30-2009, 07:25 PM

Quote:

Originally Posted by Moderator4SS

Better than paying $117.00 on Ebay

... $50 is nothing if the cosmetic mod is right. I was the guinea pig, so you should be thanking me...

Well, I thank you for being the first to get one. If you do not like the part please let me know. If you want to return it we will refund you purchase.

Thanks, Roger

dragonZ28 · 09-30-2009, 07:27 PM

Quote:

Originally Posted by Moderator4SS

The product is quality, for sure... just needs some refining. There are a few fingerprints on it and a little debris in the cupholder, but I wanted to give it a realistic look. I zoomed in on it, so people could see an untouched photo. This is a good idea and will sell plenty if it can be refined properly. IMO, the middle of the insert should be semi open instead of connected.

We also make it with the opening in between. In fact they are going out in the mail tomorrow.

Thanks, Roger

Mod4SS · 09-30-2009, 07:29 PM

Quote:

Originally Posted by Wyld Irish

I hope I didn't make it sound like I was bagging on your insert. The insert is great .. good lines on the metal and the cuts are nice a crisp .. no spurs .. totally top notch.

I was just tossing out a way to camouflage where the metal and plastic meet. For those who are looking for something like that.

It's all good, I appreciate the clarification. I like your idea about the camouflage where the metal and plastic meet, good suggestion.

Mod4SS · 09-30-2009, 07:38 PM

Quote:

Originally Posted by dragonZ28

Well, I thank you for being the first to get one. If you do not like the part please let me know. If you want to return it we will refund you purchase. Thanks, Roger

Thank you Roger! Maybe we could do an exchange for the other version with the opening in the middle? PM on its way...

dragonZ28 · 09-30-2009, 07:41 PM

Quote:

Originally Posted by Moderator4SS

Thank you Roger! Maybe we could do an exchange for the other version with the opening in the middle? PM on its way...

It will be the same piece, just with the center removed, will this be ok?

Please let me know,

dlara01 · 09-30-2009, 10:24 PM

Does anyone know of a clip on cup holder to slove the problem of not being able to shift with a large cup in the current location?

Defenderworx · 10-01-2009, 11:20 AM

Quote:

Originally Posted by ralyrat

http://cgi.ebay.com/ebaymotors/2010-...Q5fAccessories

Anyone know who manufactures this? We have a few vendors looking for something like this and I'd like to pass it on to them...

Mod4SS · 10-01-2009, 07:01 PM

Quote:

Originally Posted by Defenderworx

Anyone know who manufactures this? We have a few vendors looking for something like this and I'd like to pass it on to them...

I would recommend contacting EBay member "Toddsnake". He said that he manufactures the part himself.

09-30-2009, 06:47 PM	#43
Wyld Irish Drives: CGM 2010 SS/RS Manual Join Date: Sep 2009 Location: Little Rock, AR Posts: 58	It's probably a bit late for this ... and your going to think I'm crazy. But get a 2 x 2 square of black felt. Cut it to match the insert plate. Then glue it (felt side up) to the bottom of the plate. Press it really hard (a press if you have one ... some really heavy books if you don't) while it drys. Your trying to get just a little edge (very little edge) of the felt to stick out from the insert plate edges. This will help cover that metal to plastic rough edge look. and should only run you about 4 bucks... __________________ I never drive faster then I can see. Besides ... it's all in the reflexes.

09-30-2009, 07:10 PM	#45
Wyld Irish Drives: CGM 2010 SS/RS Manual Join Date: Sep 2009 Location: Little Rock, AR Posts: 58	I hope I didn't make it sound like I was bagging on your insert. The insert is great .. good lines on the metal and the cuts are nice a crisp .. no spurs .. totally top notch. I was just tossing out a way to camouflage where the metal and plastic meet. For those who are looking for something like that. __________________ I never drive faster then I can see. Besides ... it's all in the reflexes.

09-30-2009, 07:23 PM	#47
dragonZ28 Drives: 2001 T/A, 2010 2SS/RS, 2006 Z06 Join Date: Apr 2009 Location: Lexington, KY Posts: 2,428	The picture we took above in our post was a very clean car, a very cleaned up part, "the way it should be" taken with plenty of light etc..... You guys can use your own judgement. I also have more pictures if needed. Thanks, Roger Last edited by dragonZ28; 09-30-2009 at 08:38 PM.

09-30-2009, 10:24 PM	#54
dlara01 Drives: camaro Join Date: Jul 2009 Location: phx Posts: 17	clip on cup holder Does anyone know of a clip on cup holder to slove the problem of not being able to shift with a large cup in the current location?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What beer does your camaro drink?	ChevyNut	Off-topic Discussions	62	10-11-2010 09:19 PM
Who will Win the Stanley Cup??	bluch	The Sports Lounge	117	06-15-2009 06:50 AM
the 86 rules of drinking	Wm Holden	Off-topic Discussions	13	12-13-2008 12:36 PM

09-30-2009, 06:53 PM	#44
dragonZ28 Drives: 2001 T/A, 2010 2SS/RS, 2006 Z06 Join Date: Apr 2009 Location: Lexington, KY Posts: 2,428	In our product's defense, those pictures make the part look scratched up and really somewhat misrepresent the insert. There is debris and fingerprints all over that piece. Here is what the item looks like in our photo in our car: A picture can make something look bad when it really isn't. Please don't rush to judgement from photos. It is a quality product.