10-29-2021, 09:15 PM | #1 |
Drives: 2018 ZL1 Join Date: Jun 2021
Location: Pearland, TX
Posts: 37
|
ZL1 factory calipers-2018 1900 miles
REMOVE-SOLD
I have replaced my brake calipers with the red 1LE calipers so mine are available. They came off of a 2018 ZL1 with 1900 miles that has not yet been tracked nor seen any rain. Obviously I have all of the boxes from what I just bought so shipping should be relatively easy. SOLD *Buyer pays shipping but know that I have a discounted shipping option that only cost me $37 to ship the wrong fronts I was sent back to the seller recently. Last edited by kgerm; 11-04-2021 at 10:16 AM. Reason: SOLD |
10-30-2021, 08:45 AM | #2 |
Drives: 2010 2SS/RS Join Date: Dec 2009
Location: Clarksville Tennesse.
Posts: 6,063
|
PM’d
__________________
Orange Krush II
1LE Front sway bar, Splitter, shocks and struts, Z28 dual mode mufflers, Intake, UCA Bushings, and Toresen 3.91 Diff. 1 piece DSS Drive Shaft, ZL1/C7 Calipers, and 32mm JPSS Rear Bar. ASC race spec splitter and wicker. 6th Gen M017 Wheels. Stainless Works 1 7/8 LTs. DSE and PAFDT Suspension components. |
11-02-2021, 10:40 AM | #3 |
Chief Bief
Drives: Nightfall Gray Camaro 1SS Join Date: Dec 2015
Location: Norfolk, Virginia
Posts: 208
|
Still available?
__________________
2016 NFG 1SS M6 JLT Intake, LT2 Manifold, LT5 TB, CSP 2" headers, AWE Catback Exhaust, Apex ARC-8 Wheels. 426whp/434wtq |
11-02-2021, 01:15 PM | #4 |
Drives: 2018 ZL1 Join Date: Jun 2021
Location: Pearland, TX
Posts: 37
|
|
11-02-2021, 06:54 PM | #5 |
Chief Bief
Drives: Nightfall Gray Camaro 1SS Join Date: Dec 2015
Location: Norfolk, Virginia
Posts: 208
|
Will these calipers fit on a normal SS?
__________________
2016 NFG 1SS M6 JLT Intake, LT2 Manifold, LT5 TB, CSP 2" headers, AWE Catback Exhaust, Apex ARC-8 Wheels. 426whp/434wtq |
11-02-2021, 06:54 PM | #6 |
Drives: 2016 1ss camaro Join Date: Feb 2016
Location: 909
Posts: 9,813
|
yes but u need the brackets and lines and calipers also
__________________
16 1SS NIGHTFALL GRAY METALLIC WITH NPP #BECAUSERACECAR #SAVETHEMANUALS
|
11-02-2021, 07:36 PM | #7 |
Drives: 2018 ZL1 Join Date: Jun 2021
Location: Pearland, TX
Posts: 37
|
|
11-02-2021, 08:41 PM | #8 |
Drives: 2010 2SS/RS Join Date: Dec 2009
Location: Clarksville Tennesse.
Posts: 6,063
|
An what brackets?? May need a different heat shield an lines but other than rotors, lines, and pads he should be good to go.
__________________
Orange Krush II
1LE Front sway bar, Splitter, shocks and struts, Z28 dual mode mufflers, Intake, UCA Bushings, and Toresen 3.91 Diff. 1 piece DSS Drive Shaft, ZL1/C7 Calipers, and 32mm JPSS Rear Bar. ASC race spec splitter and wicker. 6th Gen M017 Wheels. Stainless Works 1 7/8 LTs. DSE and PAFDT Suspension components. |
|
|
Post Reply
|
|
|