Homepage Garage Wiki Register Members List Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Engine | Drivetrain | Powertrain Technical Discussions > Forced Induction Discussions


Bigwormgraphix


Post Reply
 
Thread Tools
Old 01-05-2020, 07:44 AM   #1
laynlo15
 
laynlo15's Avatar
 
Drives: 2016 1ss A8, Npp
Join Date: Nov 2015
Location: clark, mo
Posts: 5,971
Who's running Frankenstein Ported Heads-Happy?

I'm still on the fence about what to do with my heads. I've found a pretty good deal on a set of Frankenstein Lt1's still in the box. They are stage 1 and looks like some really nice machining and per the website decent gains. Anyone running these and are you happy with them? Or opinions?
__________________
2016 Camaro 6.2, Magnuson 2650 Heartbreaker, RotoFab, Lt4 short block (stock) BTR Cam kit, stock heads, stock drivetrain. Kentshotrodgarage (M/T, Racestar Wheels), Best 9.40@147 Best MPH 149 1/4 5.99@119 Best MPH 120 Best 60' 1.35.

2016 C7 A8 E85, Speed Engineering LTs, Nitto 555R2s 11.18@124.76 1.63 60ft, 7.23@98.38 mph
laynlo15 is offline   Reply With Quote
Old 01-05-2020, 11:41 AM   #2
scooter k
 
Drives: wife's car
Join Date: Jan 2011
Location: Iowa
Posts: 198
Had mine done there. They look amazing!
scooter k is offline   Reply With Quote
Old 01-05-2020, 12:20 PM   #3
ramairroughneck
 
Drives: 2018 Camaro SS
Join Date: Sep 2009
Location: Oklahoma
Posts: 202
I regret doing heads on my combo. I would have been so much better off to have put that money into the fuel system. Is there really an advantage to gaining power by bolting on heads when one size smaller blower pulley puts you at the same exact power?
ramairroughneck is offline   Reply With Quote
Old 01-05-2020, 12:41 PM   #4
laynlo15
 
laynlo15's Avatar
 
Drives: 2016 1ss A8, Npp
Join Date: Nov 2015
Location: clark, mo
Posts: 5,971
So true, some have been telling me they gain more buy just milling the heads. These heads are pretty dam good from the factory for sure. Good springs, correct push rods, 30 thou milling and let er eat. I def need to upgrade my low side so I could use that money to go towards DSX upgrade.
__________________
2016 Camaro 6.2, Magnuson 2650 Heartbreaker, RotoFab, Lt4 short block (stock) BTR Cam kit, stock heads, stock drivetrain. Kentshotrodgarage (M/T, Racestar Wheels), Best 9.40@147 Best MPH 149 1/4 5.99@119 Best MPH 120 Best 60' 1.35.

2016 C7 A8 E85, Speed Engineering LTs, Nitto 555R2s 11.18@124.76 1.63 60ft, 7.23@98.38 mph
laynlo15 is offline   Reply With Quote
Old 01-05-2020, 11:52 PM   #5
oldman


 
Drives: SS 6 speed of course
Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,137
Factory hollow valves are iffy. I’d go for Manley proflows in stock heads have a good conservative large seat but into them... they are as good as titanium valves without the aggressive titanium guide wear. The undercut head does give a nice boost in flow too.
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
oldman is offline   Reply With Quote
Old 01-09-2020, 09:09 AM   #6
ShizzySupra
 
Drives: 16' Camaro 2SS
Join Date: Sep 2015
Location: Oregon
Posts: 381
Quote:
Originally Posted by ramairroughneck View Post
I regret doing heads on my combo. I would have been so much better off to have put that money into the fuel system. Is there really an advantage to gaining power by bolting on heads when one size smaller blower pulley puts you at the same exact power?
The bigger power gain comes from milling the heads. The porting helps but for the most part will just help the upper end curve on most setups. For example I gained 40ish whp peak on my setup but it was 55+whp in the upper end past 6400.

There also comes a point where pulleying down is generating more heat than its worth for power gains.
__________________
@DeathWatchCamaro on Insta
993whp Magnuson 2.3R
9.5 @ 145, Magnuson 2300, Full Weight 2SS, 17’s (810whp)
ShizzySupra is offline   Reply With Quote
Old 01-09-2020, 09:20 AM   #7
laynlo15
 
laynlo15's Avatar
 
Drives: 2016 1ss A8, Npp
Join Date: Nov 2015
Location: clark, mo
Posts: 5,971
Thanks Shizzy, decided to stay with my stock heads, new BTR platinum spring kit. I think we will probably do a little milling since I'm starting off with an Lt4 short block which is 10.0 compared to my shit short block we just took apart which was 10.5. Probably about 20 thou and then we will see if its gonna require a shorter push rod.
__________________
2016 Camaro 6.2, Magnuson 2650 Heartbreaker, RotoFab, Lt4 short block (stock) BTR Cam kit, stock heads, stock drivetrain. Kentshotrodgarage (M/T, Racestar Wheels), Best 9.40@147 Best MPH 149 1/4 5.99@119 Best MPH 120 Best 60' 1.35.

2016 C7 A8 E85, Speed Engineering LTs, Nitto 555R2s 11.18@124.76 1.63 60ft, 7.23@98.38 mph
laynlo15 is offline   Reply With Quote
Old 01-09-2020, 11:13 AM   #8
L78toLT1

 
L78toLT1's Avatar
 
Drives: Hyper Blue 2016 2SS 6M
Join Date: Sep 2017
Location: North Ga
Posts: 1,054
Which lifters are you planning to run, Greg? Lots of posts badmouthing LS7's, but I haven't seen too many reported failures. I'm on the LS7's with my .635 lift cam but may upgrade when I refresh the heads. I have around 10K on these springs/lifters, planning to refresh at around 25K. I wonder how the guides hold up with the typical aftermarket cams/springs?
__________________
Baby Blue
2016 Hyper Blue 2SS/6m/MRC/NPP/Silver Rally stripes/ZL1 wheels/6 piston Brembo's/GForce DS and axles/ZLE Cradle Bushings/FE4 ARB front & rear/SEMA Grill/Rotofab dry/Pray ported TB/Magnuson Heartbeat with 85mm pulley/Full LT4 fuel system/JMS boost-a-pump/Skidmark Garage E85 Sensor/JRE Smooth Idle Cam/GPI piston/rod kit /APR main, head, balancer bolts/Kooks 1 7/8 headers with high flow cats/JRE remote tuned
L78toLT1 is online now   Reply With Quote
Old 01-09-2020, 12:08 PM   #9
laynlo15
 
laynlo15's Avatar
 
Drives: 2016 1ss A8, Npp
Join Date: Nov 2015
Location: clark, mo
Posts: 5,971
That's the lifters I was running. Perfect condition along with the cam. I'd have to check what lifters BTR uses but it is a BTR cam kit w/lifters in this new short block.
__________________
2016 Camaro 6.2, Magnuson 2650 Heartbreaker, RotoFab, Lt4 short block (stock) BTR Cam kit, stock heads, stock drivetrain. Kentshotrodgarage (M/T, Racestar Wheels), Best 9.40@147 Best MPH 149 1/4 5.99@119 Best MPH 120 Best 60' 1.35.

2016 C7 A8 E85, Speed Engineering LTs, Nitto 555R2s 11.18@124.76 1.63 60ft, 7.23@98.38 mph
laynlo15 is offline   Reply With Quote
 
Post Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:52 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2020, vBulletin Solutions, Inc.