03-08-2020, 04:48 AM | #7953 |
Drives: Camaro 50th anniversary edition Join Date: May 2017
Location: Europe
Posts: 2,203
|
Do you have the DIY for the recline mod? I really like you highly professional lifting tools (kitchen paper)
__________________
Soleil
_____________________________________________ A car is fast enough, if you fear to unlock it in the morning." (Walter Roehrl) |
03-08-2020, 09:48 AM | #7954 | |
Drives: 2018 Chevy Camaro RS Join Date: Mar 2019
Location: Georgia
Posts: 43
|
Quote:
AWESOME!!! How did you add the Red trim to the front splitter? Is that just red trim tape? I was thinking about doing that to my Front Splitter and Side Skirts. |
|
03-08-2020, 09:50 PM | #7955 |
Drives: 2018 Camaro SS 1LE Join Date: Oct 2019
Location: New Jersey
Posts: 255
|
Installed borla atak axle back!
Installed a borla atak axleback with the help from my uncles friend who let us use his lift (helped a ton)! This system is awesome
|
03-09-2020, 01:48 AM | #7956 |
Makis
Drives: 2020 Red Hot ZL1 A10 Join Date: Apr 2019
Location: London - UK
Posts: 806
|
This is the exhaust that I want to install. Can you post any videos?
Last edited by MakCamaro; 03-11-2020 at 02:25 AM. |
03-09-2020, 03:53 PM | #7957 |
Drives: 2018 Camaro SS 1LE Join Date: Oct 2019
Location: New Jersey
Posts: 255
|
|
03-09-2020, 06:28 PM | #7958 |
Drives: 18 Camaro LS M6 Join Date: Apr 2019
Location: NH
Posts: 698
|
EZ Gauge Dash Gauge Pod install
Just thought I would share a trick I used to get a hole in the window vent duct. Get a piece of 3/4 copper and your handy dremel. Don't have one yet? now you have a reason. Use a metal wheel and a hammer and shape the pipe like such. It will clear. I appreciate my dentist now...lol. seeing the edge of the duct end. Back up... If you push the oem vent back a bit there is a slight opening in the seam to use your PLASTIC Body tool Only! Wedge or pull the eom vent out and wire your gauges like so. You Dont Have to remove the side panel to do this, but it helps. Wedge the side panel hard and it will pop. You want to go into the duct about an inch and a half. Heat this baby HOT and position accordingly. Press the Die down and voila, you have your wiring channel through the window vent duct. Good Luck! Sorry the uploader decided to place the picture sideways.
__________________
.
. . NFG M6 2T Mishimoto Hot side pie | ZZP Catted DP | KN Drop in | Borla - Sport Tour | Apex Arc 8 - square | Wookster Tuning+ | Flex Fuel Last PB 4.8, 13.2@106 |
03-10-2020, 05:22 PM | #7959 |
Camaro2SS18
Drives: 2018 Chevrolet Camaro 2SS Join Date: Feb 2020
Location: Northern NY
Posts: 81
|
I have received my GM CAI, Mishimoto Oil Catch Can, Seat Belt Covers, GM Convertible Windscreen and Lloyd Mats Trunk Mat that I had ordered. Now as soon as spring finally arrives for good and the roads are cleaned up from all the salt and sand, I will be getting it out of storage and I will be installing everything with pictures to follow. Then I will be off to the ACS Composites Factory to have the ZL1 Aeropack to include the side skirts, front splitter with undertray installed. Can't wait, come on spring/summer!
|
03-11-2020, 10:36 AM | #7960 | |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,623
|
Quote:
Search for "acdelco satin steel touch-up paint" on ebay or amazon, make sure the paint code matches yours, I've found G9K (or WA464C), but you can check on the service parts identification label in the trunk, under the floor cover. If the gouge is deep and long or the panel is dented, however, you want to get this fixed professionally.
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
|
03-13-2020, 07:41 AM | #7961 | |
Drives: '19 camaro 2ss Join Date: Jan 2020
Location: California
Posts: 115
|
Quote:
|
|
03-13-2020, 09:24 AM | #7962 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,623
|
It's a trivial install, you just unplug the short stubby PCV hose, mount the catch can as on the picture above, and attach the hoses. A 10-minute job even for a stinky amateur like me. Double check if you attached the in/out hoses correctly to the can.
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
03-13-2020, 12:56 PM | #7963 |
Drives: 2019 Camaro 1LE Shock Candy Join Date: Mar 2016
Location: Garage
Posts: 1,757
|
__________________
LT4 1.7 Supercharger snout ported & Meth
103 Katech TB, KATECH Custom Heads, DSX In-line fuel TSP Headers, Spec P Super Twin Clutch, TSP EL C7 CAM Diamond Piston & Manley Rods, Roto Fab Big Gulp BTR Push Rods,LS7 Lifters, ARP, FI Chiller, Kirkey Seats SJM Line Lock, Hurst Pistol Grip. 747/739 RWHP street tune - 821/794 RWHP track tune 101 octane. 2014 Mini Cooper countryman S All4 M6 daily driver |
03-13-2020, 01:19 PM | #7964 |
Drives: Camaro 50th anniversary edition Join Date: May 2017
Location: Europe
Posts: 2,203
|
Looks like OEM.
__________________
Soleil
_____________________________________________ A car is fast enough, if you fear to unlock it in the morning." (Walter Roehrl) |
03-13-2020, 03:39 PM | #7965 | |
Drives: '17 2SS convertible'20 Yukon Denali Join Date: Nov 2011
Location: Cedar Park, Texas
Posts: 2,934
|
Quote:
It is easy but be careful when removing the hoses from the intake manifold. The fitting the hose goes on is plastic, as is the manifold, and can break easily.
__________________
Richard
2017 2SS SIM convertible, A8, NPP, MRC, 56R wheels, GM CAI, Diode Dynamics Side Markers Delivered: 08/15/2016 #TeamBeckyD |
|
03-13-2020, 06:02 PM | #7966 |
Drives: 2017 Camaro 2LT RS 3.6L Join Date: Mar 2016
Location: Orange Park, Florida
Posts: 1,313
|
Do you ever just look out and look at your car?
|
|
|
Post Reply
|
|
|