11-15-2016, 10:09 AM | #1 |
Drives: 2011 2SS Inferno Orange Join Date: Oct 2013
Location: Cedar Hill, MO
Posts: 60
|
LSA tuning day TODAY
The last two months have been a lot of work on my 2011 Camaro SS.
Started with the 3:91 gear swap, and urethane sub frame bushings. Swapping out the SS pump for a ZL1 unit at the same time, along with a ADM FPCM. Once done I tested that a couple of times and began installing my LSA conversion. I bought the used ADM kit from another C5 member. Adding some ID 850s and wire harness extensions from ADM along the way. I've been in no hurry, I work a lot of hours but she's finally all ready and a Tuner by the name of Shane Hinds is on his way out to put the finishing touches that I just can't do to her. It should be a great day!!!
__________________
2011 Camaro SS
Buckets of money under hood! |
11-15-2016, 10:36 AM | #2 |
Drives: 2011 Camaro 1SS Join Date: Feb 2016
Location: Warner Robins Ga
Posts: 778
|
Whew! LSA + 3.91 = increase your tire fund.
Good luck. She will be a beast. Shane has these things figured out.
__________________
2011 SGM Camaro 1SS/RS A6 - Vengeance Racing built/tuned. 590RWHP/560RWTQ, ADM LSA Conversion, 2.5 Grip-Tec, ZL1 fuel pump, ADM FPCM, FIC1000, VRPD2 Cam and LS3 Conversion with all the internal goodies, American Racing 1 7/8 Headers, no cats, SW Retro Cat Back, ADM Intake, AFCO HX, Varimax Pump, Rotofab Reservoir, B&M Transmission Cooler, VMAX TB, Elite Engineering CC, BMR LCAs, Trailing Arms, Toe Rods, DSS 1000hp axles, ZL1 Bumper and Sideskirts, Night Owl Halos, Matte Black 20" Rohana RC-22 with 20x10-275s/20x11-315s, R1 Concept Premier Drilled/Slotted Rotors, Hawk Ceramic Pads.
|
11-15-2016, 12:55 PM | #3 |
"Cam Only"
|
3.91's with this blower make for a lot of fun. But unless you have a drag radial, it's like driving on ice the second you give it even the smallest amount of throttle hah
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
11-15-2016, 01:09 PM | #4 | |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Quote:
-Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
|
11-15-2016, 01:43 PM | #5 |
Drives: 2010 2SS, 2017 Silverado LTZ Join Date: Jan 2007
Location: Denver,PA
Posts: 3,195
|
That's why I never changed the gears in the rear.
__________________
2010 2SS/RS Victory Red, MN6, 1-7/8 Kooks LT Headers, SLP Axle Back, Edelbrock E-Force S/C, ZL1 Fuel Pump, 72# Injectors, JRE fuel rail upgrade, Roto-Fab CAI, Elite Catch Can, Billet Hurst Shifter, DSS 1000HP axles, Spohn Trailing Arms, Toe Links, Lower Control Arms. Chrome American Racing Torq-Thrust wheels. 546/rwhp & 522/rwtq & 10.9# boost Tune by Jeremy Formato.
|
11-15-2016, 03:53 PM | #6 |
Too much is never enough!
Drives: AGP TT SS [COTW] 4/20/15 Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,149
|
I foresee a gear change in his future.
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq
Build thread http://www.camaro5.com/forums/showth...55#post8107855 |
11-15-2016, 05:14 PM | #7 |
Drives: 2011 2SS Inferno Orange Join Date: Oct 2013
Location: Cedar Hill, MO
Posts: 60
|
Well it runs like an absolute beast, the clutch however is the first victim!
My plan was clutch and driveshaft over the winter, then drag radial NT05 or the like. Axle shafts if needed. However It appears the clutch will require immediate attention.
__________________
2011 Camaro SS
Buckets of money under hood! |
11-15-2016, 07:20 PM | #8 |
Drives: 2013 Camaro SS 1LE Join Date: Oct 2014
Location: earth
Posts: 288
|
not to hijack the thread but has anyone gone from 3.91 to 3.45 for blower use?
|
11-15-2016, 07:34 PM | #9 |
Drives: 2011 Camaro 1SS Join Date: Feb 2016
Location: Warner Robins Ga
Posts: 778
|
I believe Hammdo had 3.91s at one time and went to 3.45s.
__________________
2011 SGM Camaro 1SS/RS A6 - Vengeance Racing built/tuned. 590RWHP/560RWTQ, ADM LSA Conversion, 2.5 Grip-Tec, ZL1 fuel pump, ADM FPCM, FIC1000, VRPD2 Cam and LS3 Conversion with all the internal goodies, American Racing 1 7/8 Headers, no cats, SW Retro Cat Back, ADM Intake, AFCO HX, Varimax Pump, Rotofab Reservoir, B&M Transmission Cooler, VMAX TB, Elite Engineering CC, BMR LCAs, Trailing Arms, Toe Rods, DSS 1000hp axles, ZL1 Bumper and Sideskirts, Night Owl Halos, Matte Black 20" Rohana RC-22 with 20x10-275s/20x11-315s, R1 Concept Premier Drilled/Slotted Rotors, Hawk Ceramic Pads.
|
11-15-2016, 08:41 PM | #10 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Yep, sure did, 3.91s with my A6 was just too much. Drove it a week that way and just crazy. 1st and 2nd were really useless, just give it a bit too much gas and spin city. Cloud of smoke is cool, but those damn tires cost too much. Even with drag radials, my combo was just too much. Some may do good with it, but ADM and just about every one else said 3:45s. That's what I did, and I'm glad...
Still get 20+ mpg, if I stay out of the gas... -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
11-15-2016, 11:32 PM | #11 |
"Cam Only"
|
Yeah I can still get 22-24mpg on 91 on the freeway.
16-17mpg on E85 Love this setup. Rips through the gears when I want to.
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
11-16-2016, 09:03 AM | #12 |
Too much is never enough!
Drives: AGP TT SS [COTW] 4/20/15 Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,149
|
I went from 345 to 323's love it. I also get 20mpg on the highway at 80mph.
Sent from my iPhone using Tapatalk
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq
Build thread http://www.camaro5.com/forums/showth...55#post8107855 |
11-16-2016, 12:03 PM | #13 |
Drives: 2010 Camaro 2SS Cyber Gray Join Date: Jul 2009
Location: El Paso, Texas
Posts: 1,132
|
on mileage I get 15-16 combined is this about right?
__________________
|
11-17-2016, 06:55 PM | #14 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Yep, pretty close. City/highway combined.
-Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
|
|
|
|