[lcarney1977]

if you go with 30s u dont need a spacer only on the 35s you do..

[MIAMI2SSRS]

Yes on the spacer information. Thank you OP. I was also surprised that is no rubbing on the back. 315s look great in the car!!

[bybcous]

I run 285/35/20 up front for 30k with no rubbing. Good to know 315 works in rear, I will be switching to 315s when the time comes.

[Carlos_MRRWheelsInc]

Originally Posted by Cmyskill

Attachment 883359

Attachment 883360

Attachment 883361

Attachment 883367

Ok, I finally found time to add my MRR M017 in gloss black to my A10 ZL1. I chose to go with the Nitto NT01 in a 315x30x20 in the rear and a 285x35x20 in the front. The rear tires fit perfect with NO rubbing issues. However, the front was a different story, and did rub on the shock tower. I added a 3mm Spacer and no rubbing so far, I really hate the fact that I had to add it.... grrr

As for the ride it feels about the same as the stock tires but there is a bit more road noise, not a lot but definitely noticeable. After a few minutes driving I completely forgot about it and I just focused on the sound of the engine.

As for Traction, the Nitto NT01's stick big time. Hitting 3.3 seconds 0-60 is quite common and the tires and wheels are my only performance mods to date. My best 0-60 time on stock tires was 3.5 seconds. (on the street not the track)

The slightly larger tires fill the fender-wells pretty good with out lifting the car to much. From the back the tires look super aggressive and give the car an amazing stance. The Rear tires measure about 12.3 inches from outside to inside.

Now, I am trying to decide if I should lower the car? I really do not want to make the car a pain to drive and I know adding lowering springs sometimes leads driving issues.

Also, a special thanks to Paul at PK Auto design for the wheels, tire setup and they were perfectly mounted and balanced.

Awesome review and great information. on the side note thank you for supporting our brand, the car looks amazing

[PK Auto Design]

Looking good brotha !

[Armando_MRRWHEELS]

The MRR M017 is one of my favorite Wheels.

Originally Posted by Cmyskill

Attachment 883359

Attachment 883360

Attachment 883361

Attachment 883367

Ok, I finally found time to add my MRR M017 in gloss black to my A10 ZL1. I chose to go with the Nitto NT01 in a 315x30x20 in the rear and a 285x35x20 in the front. The rear tires fit perfect with NO rubbing issues. However, the front was a different story, and did rub on the shock tower. I added a 3mm Spacer and no rubbing so far, I really hate the fact that I had to add it.... grrr

As for the ride it feels about the same as the stock tires but there is a bit more road noise, not a lot but definitely noticeable. After a few minutes driving I completely forgot about it and I just focused on the sound of the engine.

As for Traction, the Nitto NT01's stick big time. Hitting 3.3 seconds 0-60 is quite common and the tires and wheels are my only performance mods to date. My best 0-60 time on stock tires was 3.5 seconds. (on the street not the track)

The slightly larger tires fill the fender-wells pretty good with out lifting the car to much. From the back the tires look super aggressive and give the car an amazing stance. The Rear tires measure about 12.3 inches from outside to inside.

Now, I am trying to decide if I should lower the car? I really do not want to make the car a pain to drive and I know adding lowering springs sometimes leads driving issues.

Also, a special thanks to Paul at PK Auto design for the wheels, tire setup and they were perfectly mounted and balanced.

[Ak1LE]

Curious if I can get those same wheels made in a 19x10 and 19x11 with 1le offsets...

[Carlos_MRRWheelsInc]

Originally Posted by Ak1LE

Curious if I can get those same wheels made in a 19x10 and 19x11 with 1le offsets...

oh man sorry we dont make those specs but our new M716 will be available
in those 19x10 front and 19x11 rears
and yes rumors are true we will also have a 19x10.5 front.

[bubbajan21]

Are you using the NT01 tires as a street tire? Curious to see how long those 100TW tires will last you.

[PK Auto Design]

Originally Posted by Ak1LE

Curious if I can get those same wheels made in a 19x10 and 19x11 with 1le offsets...

Not yet brotha.