You are browsing camaro6 
03-31-2021, 12:12 AM
|
#1 |
 Drives: 2021 Camaro 2SS 1LE Join Date: Aug 2020
Location: San Ramon, CA
Posts: 5
|
Uneven ride height questions
What’s Up...
I installed Eibach Pro’s about 100 miles ago and noticed my driver side rear is about 3/8” higher than the passenger side rear. Spring is seated correctly. Any ideas on what can be wrong or is this normal? |
|
|
|
03-31-2021, 03:47 AM
|
#2 |
 
Drives: 2018 Camaro SS Join Date: Jan 2021
Location: Washington
Posts: 577
|
If it’s seeded right possible bent suspension? I’d have checked out.
Sent from my iPhone using Tapatalk |
|
|
|
|
03-31-2021, 05:42 AM
|
#3 | |
 
Drives: 2017 Camaro SS, 2011 Corvette GS Join Date: Feb 2019
Location: Erlanger, Kentucky 41018
Posts: 815
|
Quote:
It is better to measure height from the ground to a point on the frame of the car near that corner of the car. Variations in body panels, etc. can cause a lot of variation if you are just measuring wheel gap. Beyond that, it could be a week shock, bad or week bushings. Could be that that spring is not correct from Eibach. |
|
|
|
|
|
03-31-2021, 05:52 AM
|
#4 |
   
Drives: 08 Tiburon GS, 2018 Camaro 2.0T Join Date: Sep 2017
Location: Québec
Posts: 1,657
|
Sometimes it could be as stupid as an uneven ground. The sway bar will make it sit uneven. Try to check it on a very leveled surface like the gas station concrete slabs.
__________________
2018 Camaro LS | 6 spd | 2.0L turbo | Nightfall Grey | RS package | Technology Package.
--------------------- Order WDGHKX 1100 - 5/08/2018 | 3800 - 6/18/2018 2000 - 5/09/2018 | 4200 - 6/21/2018 3000 - 5/28/2018 | 5000 - 6/27/2018 6000 - 6/29/2018 |
|
|
|
|
03-31-2021, 09:53 AM
|
#5 |
|
Drives: 17 hyper blue 2SS M6 Join Date: Mar 2018
Location: NorCal
Posts: 594
|
Mine was off side to side with BMR springs, it as about the same, 1/4-3/8". Springs were fine, suspension fine, disconnected the sway bars, everything was fine it was just off. No added weight in the car, nothing ... It was just off. I have since installed coilovers and dialed it in better.
|
|
|
|
|
03-31-2021, 03:02 PM
|
#6 |
|
Old school tech
Drives: Ruby 1LE - 2024 2SS 1LE Join Date: Mar 2014
Location: San Antonio, TX
Posts: 288
|
Were the springs marked for their sides? If so, it's not uncommon for them to make the driver side a little higher to compensate for the driver's weight.
|
|
|
|
|
03-31-2021, 03:06 PM
|
#7 |
Drives: 2017 Silverado/2017 ZL1 Join Date: Aug 2019
Location: Jax/Palatka FL
Posts: 1,090
|
Eibach springs are trash. I had some on my fbody and switch to BMR springs because the Eibachs were prone to uneven sagging. I will never buy eibach again, either stock or BMR
__________________
 |
|
|
|
|
|
|
|
|
Post Reply
|
|
|
