06-14-2023, 09:18 AM | #1 |
Drives: 2018 Hot Red ZL1 Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 3,599
|
Coolant hose connection questions
Does anyone know the torque specs for the bolts on coolant hose connection to the engine block in the picture?
Also, does anyone know the type of bolt? I am installing the catch can on one of those bolts and the bracket is about less than 1/2 inch thick so i would like to get a longer bolt. Would that longer bolt even be necessary? I have seen in other MY they changed the style of how that part connects to the engine block.
__________________
|
06-14-2023, 01:48 PM | #2 |
Drives: 2020 Chevy Camaro ZL1 Join Date: Apr 2023
Location: Calgary Canada
Posts: 1,483
|
Sorry I don’t, I chose to put it on the drivers side of engine
|
06-14-2023, 01:51 PM | #3 |
Thank you Al Oppenheiser!
Drives: Red Hot A10 ZL1 Convertible Join Date: Jun 2017
Location: Sarasota, FL
Posts: 4,978
|
Photo is blurry so I can't see what you see. But here is the LT4 stuff from the whole torque table. New bolt should have the same markings as the current bolt, just be longer. You can usually deduce the bolt spec from the torque spec.
Engine Oil Cooler Bolt 10 N.m (89 lb in) Engine Oil Cooler Hose Fastener (LT1, LT4) 10 N.m (89 lb in) Engine Oil Cooler Hose Quick Connect 34 N.m (25 lb ft) Radiator Air Lower Seal Bolt 2.5 N.m (22 lb in) Radiator Surge Tank Nut 6 N.m (53 lb in) Radiator Upper Mount Bracket Bolt 9 N.m (80 lb in) Supercharger Water Manifold Fastener (LT1, LT4) 10 N.m (89 lb in) Thermostat Heater Shield Fastener 5 N.m (44 lb in) Upper Charge Air Cooler Bracket Bolt (LGX LTG LT4) 9 N.m (80 lb in) Water Inlet and Outlet Pipe Fasteners 9 N.m (80 lb in) Water Outlet Bolt (LTG, LT1, LT4) 10 N.m (89 lb in) Water Pump Bolt (LT1, LT4) 10 N.m (89 lb in) Air Bleeder Valve Pin Screw (LT4) 2.8 N.m (25 lb in) Charge Air Cooler Bracket Bolt (LGX LTG LT1 LT4) 9 N.m (80 lb in) Charge Air Cooler Bracket Bolt (LTG LT4) 22 N.m (16 lb ft) Charge Air Cooler Coolant Pump Clamp Bolt (LT4) 9 N.m (80 lb in) Charge Air Cooler Radiator Bolt (LT4) 9 N.m (80 lb in) Charge Air Cooler Upper Bracket Nut (LT4) 5.5 N.m (49 lb in) Drain Plug (LT4) 9 N.m (80 lb in) Engine Coolant Air Bleed Valve (LT1 LT4) 12 N.m (106 lb in) Engine Coolant Fan Bolt (LT4) 9 N.m (80 lb in) Engine Coolant Manifold Bolt (LT1, LT4) 25 N.m (18 lb ft) |
06-25-2023, 10:41 PM | #4 | |
Drives: 2018 Hot Red ZL1 Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 3,599
|
Better pics below. It is the coolant hose attachment to the engine.
Quote:
__________________
|
|
06-26-2023, 07:34 AM | #5 |
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: Petersham MA
Posts: 4,758
|
That is the thermostat housing FYI.
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors, LPE BB HPFP, 15” conversion 1059 WHP/944 WTQ, 9.48@150
|
06-26-2023, 07:53 AM | #6 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,619
|
89 inch (not foot!) pounds, see below
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
07-02-2023, 07:34 PM | #7 |
Drives: 2018 Hot Red ZL1 Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 3,599
|
Thank you all for the assistance. Do you all think I need a longer bolt if I add a bracket to one of the bolts? The bracket is like 1/4 inch. I suppose I can go to a lower store and get a longer bolt for piece of mind.
__________________
|
|
|
Post Reply
|
|
|