11-23-2019, 11:20 AM | #1 |
Drives: 2016 Chevrolet Camaro 1SS Join Date: Sep 2019
Location: Hawaii
Posts: 19
|
MSD Intake with 103mm Nick Williams TB
Im wondering if its ok to go ahead and install my Atomic MSD Intake Manifold along with my 103mm Nick Williams throttle body on my 2016 camaro ss and wait about 1-2 weeks before tuning. All i have installed so far is a rotofab dry filter CAI. Eventually i want to go LT catless headers back and am needing suggestions on whether or not to keep npp and afm or delete both and go full send. I know quad tips looks good but is it worth it or is it better to go single pipes out wach side?
|
11-23-2019, 11:32 AM | #2 |
Drives: 2016 Camaro 2SS Join Date: Apr 2018
Location: Central Texas
Posts: 1,011
|
You can go ahead and install them but if it was me I wouldn't drive the car untill it gets tuned.
|
11-23-2019, 11:55 AM | #3 | |
Quote:
__________________
DMS Flex Fuel-E85
HPTuners Ngauge Roto Fab CAI, LPE Ported/Polished 95mm LT5Throttle Body, PRAY Ported MSD Intake Manifold, SP Coated TSP 1 7/8" Catlless Longtubes Hooker BlackHeart Cat-Back, Mishimoto Catch Can (Which always has some nasty in it) Instagram@Weapon_6 |
||
11-23-2019, 11:59 AM | #4 |
Drives: 2016 Chevrolet Camaro 1SS Join Date: Sep 2019
Location: Hawaii
Posts: 19
|
What do you mean by send to get ported? The throttle body and msd are both 103mm and ready to connect to each other. I appreciated the speedy replies also.
|
11-23-2019, 03:01 PM | #5 |
Porting of the intake runners not the TB opening.
__________________
DMS Flex Fuel-E85
HPTuners Ngauge Roto Fab CAI, LPE Ported/Polished 95mm LT5Throttle Body, PRAY Ported MSD Intake Manifold, SP Coated TSP 1 7/8" Catlless Longtubes Hooker BlackHeart Cat-Back, Mishimoto Catch Can (Which always has some nasty in it) Instagram@Weapon_6 |
|
12-01-2019, 11:53 PM | #6 |
Drives: SS 6 speed of course Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,316
|
Ran that combo with CA car deletes and a stock tune with rear o2s turned off with no issues.
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
|
12-03-2019, 08:40 AM | #7 |
Drives: 17 Camaro SS Join Date: Nov 2019
Location: Central VA
Posts: 117
|
I'm interested in how much this combo adds to power. I'm also planning this mod next year after I get a few more miles on the car. Don't want to kill my warranty too soon.
|
12-03-2019, 09:34 AM | #8 |
Account Suspended
Drives: 2012 2SS CAMARO 45th Join Date: Apr 2011
Location: St. Charles, IL
Posts: 18,663
|
We've done a few set ups similar to this and the car was pretty lean. You should be fine to drive it to the tuner and what not but I wouldn't daily it very long before getting it tuned.
|
12-03-2019, 10:47 AM | #9 |
Drives: 2018 Camaro ss Join Date: Jul 2019
Location: North Atlanta, Ga.
Posts: 147
|
I'd honestly wait to install till you cand do the tune immediately after. Its going to make your engine run hotter then normal and you not going to see any benefits without a tune adjustment anyways.
|
12-03-2019, 01:47 PM | #10 |
This is exactly what i did to my car.
Rotofab CAI Nick Williams tb MSD manifold Kooks 1 7/8 headers Put 470hp to the ground when tuned.
__________________
2018 Camaro SS 1LE - 2011 370z - 2004 VW R32 - 2000 Civic Si Mods: Rotofab, Nick Williams 103mm TB, MSD IM, Kooks 1 7/8 Results: 470 hp / 447 tq |
|
12-03-2019, 04:16 PM | #11 |
Drives: Chevy Camaro Join Date: May 2019
Location: East Coast
Posts: 61
|
|
12-09-2019, 05:47 PM | #12 |
Drives: 2016 Chevrolet Camaro 1SS Join Date: Sep 2019
Location: Hawaii
Posts: 19
|
|
12-10-2019, 01:40 PM | #13 | |
Quote:
I think all parts and labor totaled $5k No exhaust for me, the headers with hi-flo cats is plenty loud!
__________________
2018 Camaro SS 1LE - 2011 370z - 2004 VW R32 - 2000 Civic Si Mods: Rotofab, Nick Williams 103mm TB, MSD IM, Kooks 1 7/8 Results: 470 hp / 447 tq |
||
12-12-2019, 04:53 PM | #14 |
Drives: 1SS Summit White 6 speed Join Date: Jul 2017
Location: Gainesville GA
Posts: 579
|
470 is great for bolt ons.
What did you baseline stock?
__________________
16 1SS M6 White
Magnuson 2.3 Heartbeat Roto Fab Solo Performance Cat deletes and Axleback Hurst short shifter #'s coming soon Riaction coilovers 1LE sway bars BMR mm BMR chassis brace Flow one 19" wheels wrapped in Mickey Thompsons 02 Z28 M6 35th anniversary 80k miles T-tops Leather Bolt ons Joy to drive this classic every day! Daily Driver |
|
|
Post Reply
|
Tags |
long tube headers, msd atomic airforce, nick williams, roto fab cold air intake |
Thread Tools | |
|
|