08-17-2017, 12:08 PM | #127 | |
Drives: 18 ZL1 A10 Join Date: Nov 2008
Location: South East, FL
Posts: 3,024
|
Quote:
A good corrected number is 2 1/2 all around. -bobby
__________________
2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6
ZL1::J-E-T-S JETS JETS JETS |
|
08-17-2017, 02:09 PM | #128 |
Drives: 2017 Camaro ZL1 Join Date: Aug 2014
Location: Dallas
Posts: 145
|
What exactly do I need to say to the people at the stealership to get this done?
My car was in for an oil change and I mentioned it to them and they gave me a run-around. Basically "we can't do anything unless you're complaining that something is wrong", to which I said "my front end sits considerably higher than my rear which seems odd", but continued to get the run around about "warranty" and this isn't covered, etc. |
08-17-2017, 02:15 PM | #129 | |
Drives: Pre-production ZL1 M6 Join Date: Feb 2016
Location: Sunbelt
Posts: 531
|
Quote:
|
|
08-17-2017, 02:24 PM | #130 |
H-Town Camaro Club Member
Drives: 17 Hyper Blue Metallic KLR-ZL1 Join Date: May 2009
Location: Pearland Tx.
Posts: 2,035
|
Car is as level as possible. measured center of arch of fender to the same line as OP.
__________________
|
08-17-2017, 03:16 PM | #131 | |
Drives: 18 ZL1 A10 Join Date: Nov 2008
Location: South East, FL
Posts: 3,024
|
Quote:
-bobby
__________________
2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6
ZL1::J-E-T-S JETS JETS JETS |
|
08-17-2017, 04:36 PM | #132 |
H-Town Camaro Club Member
Drives: 17 Hyper Blue Metallic KLR-ZL1 Join Date: May 2009
Location: Pearland Tx.
Posts: 2,035
|
Lets compare total height from ground to center of wheel arch. I cant tell crap from just looking at a pic. LOL. Mine is 28" with about 32 PSI in the front.
__________________
|
08-17-2017, 06:28 PM | #133 | |
Drives: 18 ZL1 A10 Join Date: Nov 2008
Location: South East, FL
Posts: 3,024
|
Quote:
-Bobby
__________________
2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6
ZL1::J-E-T-S JETS JETS JETS |
|
08-17-2017, 08:56 PM | #134 |
Drives: 2017 ZL1 A10 White Vert Join Date: Aug 2017
Location: Katy Tx
Posts: 151
|
Pardon me if I missed if this is for only coupes, but my new 2017 ZL1 Vert with build date of 5/17 is 27 & 7/8" front & back from level garage floor to wheel arch, however using the tire line to wheel arch, front is 2 & 1/2" / rear is 2 & 1/4".
After my 2016 Z06 rubbed on my driveway incline and this car does not, I'm good leaving it alone as it may settle some anyway as I put more miles on the car, only have 471 miles today. |
08-17-2017, 10:28 PM | #135 | |
Drives: 18 ZL1 A10 Join Date: Nov 2008
Location: South East, FL
Posts: 3,024
|
Quote:
-Bobby
__________________
2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6
ZL1::J-E-T-S JETS JETS JETS |
|
08-18-2017, 06:50 PM | #136 | |
|
Quote:
Save
__________________
|
|
08-18-2017, 07:39 PM | #137 |
Drives: 2017 ZL1 Vert Arctic Blue Join Date: Mar 2017
Location: Phoenix, AZ
Posts: 73
|
Same here for the 'Vert. Build date 4/17; front and back from floor to fender is 27 7/8".
|
08-18-2017, 09:27 PM | #138 |
Drives: 2017 ZL1 A10 Join Date: Sep 2009
Location: Austin TX
Posts: 866
|
Here's mine. Build date: 4/17. Rear is only about an 1/8 lower than the front. I'm ok with that.
__________________
2017 ZL1
A10 Redhot with stripe |
08-26-2017, 09:34 AM | #139 |
Drives: 2017 ZL1 Join Date: Jun 2012
Location: Graniteville,SC
Posts: 645
|
Had to bring this one back. Did any of you get a resolution at the dealer yet?
|
08-26-2017, 09:43 AM | #140 |
Coupe Newbie
Drives: 2017 ZL1, 2021 Corvette Convertible Join Date: Jul 2011
Location: Columbus, Ohio
Posts: 3,281
|
I have a appointment at the dealer on Monday. I definitely will post before and after photos.
__________________
|
|
|
Post Reply
|
|
|