You are browsing camaro6 
04-26-2022, 03:46 PM
|
#1 |
 Drives: Chevy Camaro 2SS Join Date: Sep 2019
Location: California
Posts: 87
|
02 Sensor Issues w/ Data Log
My B2S1 seems to be stuck around 850 - 900mv for most of my drive. I think im going to go ahead and replace my 02 sensor. I'm a newb and learning as I go, so if anyone sees anything else or has any suggestions I would greatly appreciate it.
Thanks in advance. Last edited by 714camaro; 04-26-2022 at 10:46 PM. |
|
|
|
04-26-2022, 06:08 PM
|
#2 |
         Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,675
|
Your rear o2 sensors aren’t plugged in?
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
|
|
|
|
04-26-2022, 06:25 PM
|
#3 | |
|
Drives: Chevy Camaro 2SS Join Date: Sep 2019
Location: California
Posts: 87
|
Quote:
__________________
'16 Camaro 2SS A8, LT4 Blower (2.30 griptec), Intake, LT4 Low-Side Fuel System, Catless
|
|
|
|
|
|
04-26-2022, 06:30 PM
|
#4 |
|
Drives: Chevy Camaro 2SS Join Date: Sep 2019
Location: California
Posts: 87
|
Either way, my car just went to a new shop and they said the wiring on one of my sensors looked smushed against the heat shield so im going to take a look.
__________________
'16 Camaro 2SS A8, LT4 Blower (2.30 griptec), Intake, LT4 Low-Side Fuel System, Catless
|
|
|
|
|
04-26-2022, 08:43 PM
|
#5 |
|
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,675
|
Pretty sure you need them plugged in
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
|
|
|
|
04-26-2022, 10:44 PM
|
#6 |
|
Drives: Chevy Camaro 2SS Join Date: Sep 2019
Location: California
Posts: 87
|
So i just got under and checked the sensors. I did have all 4 in place. It was also my B2S2 that looked crammed up against my heat shield. The funny thing is my B2S1 looked perfectly fine from the outside. Still waiting on the replacement to arrive.
I’ll update the thread with the photos i took in the mean time. Photos are ordered B2S1, B1S1, B2S2 Update: I'm also just now noticing what looks like oil around my oil filter seal in the first 02 photo. I probably over tightened it.
__________________
'16 Camaro 2SS A8, LT4 Blower (2.30 griptec), Intake, LT4 Low-Side Fuel System, Catless
Last edited by 714camaro; 04-27-2022 at 12:31 AM. |
|
|
|
|
|
|
|
|
Post Reply
|
|
|
