12-13-2016, 02:25 PM | #29 | |
Drives: 2016 Nightfall Gray Metallic 1SS Join Date: Oct 2016
Location: El Monte
Posts: 10
|
Quote:
|
|
12-13-2016, 03:44 PM | #30 | |
Drives: SS 6 speed of course Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,324
|
Quote:
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
|
|
12-13-2016, 03:56 PM | #31 |
Drives: 2016 SS M6, NPP Join Date: Apr 2016
Location: Hawthorne, CA
Posts: 1,957
|
Uh oh, the oldman has spoke! Nothing but wisdom from you sir!
At first they were 28" then I shorten it down to 26" and drone is about 80% gone.. I'll take it! Chart I used Last edited by Richard0nee; 12-16-2016 at 11:10 AM. |
12-13-2016, 05:19 PM | #32 |
Drives: 16' 2SS M6 Join Date: Feb 2010
Location: Earth
Posts: 573
|
Very nice! Wish I could switch off between this setup and my Borla! Gonna post my review soon
|
12-13-2016, 05:56 PM | #33 |
Drives: 2016 SS M6, NPP Join Date: Apr 2016
Location: Hawthorne, CA
Posts: 1,957
|
|
12-13-2016, 06:19 PM | #34 | |
Drives: 2016 SS M6, NPP Join Date: Apr 2016
Location: Hawthorne, CA
Posts: 1,957
|
Quote:
With Outlaws (one inlet, one outlet) you'll need a y-pipe to the NPP tips.. so it'll be a bit more. If you're sensitive to drone (Sport/track), you'll need a J-pipe (~$100) to eliminate it. And if you're muffler shop don't know what a J-pipe is.. hmmmm lol |
|
12-17-2016, 08:36 PM | #35 |
Hey man, great job this sounds beautiful. I'm trying to replace the factory NPP with something better and I think replacing the mufflers work well for the budget. Thanks for sharing the video. I will look into this system.
|
|
04-07-2017, 10:10 AM | #36 |
Drives: SS-6-SPD Join Date: Jan 2017
Location: New Jersey
Posts: 1,364
|
sorry to bump up old thread.. but you got this muffler and cut you stock tips to match this? which size did valve go? is it me or did stock NPP on sprot / track sound louder?
http://www.flowmastermufflers.com/st...ressive-sound/ sso basicall all ill need to do to get install and weld hangers .. cut stock tops weld into this muffler? which side is straight flow? |
04-08-2017, 03:41 PM | #37 |
Drives: 2019 Camaro SS Join Date: Jan 2017
Location: Chicago
Posts: 138
|
I'm so glad I found this thread!
I've been looking for a cost effective way to get some more sound out of my NPP exhaust. Couldn't really justify paying $1500.00-2000.00 for the NPP specific setup. Thanks for the awesome and detailed pics. Printed some out and took them to my exhaust shop to use as a template. They said it shouldn't be a problem. Just ordered my Flowmaster super 10's today!
__________________
2019 Camaro 1SS. Crush. Mishimoto Catch Can, BMR Strut Tower Brace, Oracle Side Markers, ZL1 Side Skirts, Blade Spoiler W/ZL1 Addons Wicker Bill, Exhaust Cut Outs, BMR Front and Rear Cradle Braces, Cold Air Inductions CAI. ZL1 Rims 285 Fronts and 305's Rear. Speed Inc Tune PCM & TCM.
|
04-09-2017, 07:16 AM | #38 |
Drives: 16 Red Hot 2SS Join Date: Oct 2016
Location: Orlando
Posts: 198
|
Nice setup, especially with the J pipe. My straight exhaust has some tolerable drone but this will be my next step if the drone gets too much for me.
__________________
'16 Red Hot 2SS A8 sunroof
|
04-11-2017, 04:17 PM | #39 |
Drives: SS-6-SPD Join Date: Jan 2017
Location: New Jersey
Posts: 1,364
|
thanks man!
i ordered the same exhaust! it's going on tomorrow .. |
04-11-2017, 08:18 PM | #40 | |
Account Suspended
Drives: 2011 2SS/ RS INFERNO ORANGE L99 Join Date: Dec 2012
Location: Alliston Ontario Canada
Posts: 9,057
|
Quote:
|
|
04-26-2017, 04:17 PM | #41 | |
just installed
Thanks Richard0nee for this post! Finally got them installed on my car. Sounds amazing and couldn't be happier.
|
||
|
|
Post Reply
|
|
|