11-17-2019, 04:28 PM | #1 |
Drives: 2018 Camaro RS, 2018 Subaru WRX Join Date: Nov 2019
Location: Wisconsin
Posts: 3
|
Engine trouble with procharger
Just installed procharger supercharger on 2018 V6 camaro. Followed manual to a T. Procharger flashed the computer with a tune and should be good to go. Cant get engine to run more than a minute or two. Been emailing back and forth with Procharger for a week or so and can't find problem. Double and triple checked connections and vacuum lines. Handheld scanner shows normal readings from maf and map sensors. Gas pedal has little effect when engine is running. Have the P1400 code that relates to cold start problem. Intermittently get codes for low voltage on both banks of O2 sensors and numerous misfires. Havent found anything accidentally knocked loose during install. Anybody have any ideas where to go with it now?
|
11-17-2019, 09:53 PM | #2 |
Drives: 2017 Camaro 2SS A8 Join Date: May 2019
Location: USA
Posts: 1,656
|
Although I’ve had my MAF disconnected a couple times and re-connected with no problem I’d check to make sure it’s not rotated 180°. IIRC there was a video from one of the tuners showing that connector can be connected wrong. If that’s true, I was lucky twice.
I believe there’s a square shape that indicates the direction on the connection.
__________________
Roto-Fab w/sound tube delete, Katech ported TB, Pray IM, Velossa, DD side markers, DSX FF, UPR Catch can, Halo brace, My custom vent gauge pod
Originally Posted by arpad_m - “Aww, yet another oil thread with almost the same question in the OP“ |
11-19-2019, 01:37 PM | #3 |
Dyno Show Queen LOL
Drives: 16 SS & 17 ZL1 Both Yellow Join Date: Jan 2014
Location: Houston
Posts: 4,345
|
Definitely check the maf and that harness that came with the kit that plugs into the Maf and map.. Storm"the 1st centri on a v6 had a problem in those areas a long with it taking out her AC compressor.
__________________
Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber |
12-02-2019, 08:23 PM | #4 | |
waddupdgriff
Drives: Supercharged 2016 2LT RS Join Date: Sep 2017
Location: IG: waddupdgriff
Posts: 213
|
Quote:
|
|
12-05-2019, 09:36 PM | #5 |
Drives: SS 6 speed of course Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,316
|
this is what I'd do, disconnect belt to procharger flash it back to stock see if it runs. I broke in both of my engines with no supercharger on just a filter bolted to the intake tube, new procharger setup uses stock box so no issue there either.
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
|
12-05-2019, 09:37 PM | #6 |
Drives: SS 6 speed of course Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,316
|
also check vacuum leaks, did you connect up the brake booster? How about the lines that need to be moved when you moved the vac pump?
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
|
|
|
Post Reply
|
|
|