07-12-2022, 09:05 PM | #43 | |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
Quote:
Oh believe me I did feel it after a 35 mile drive in 90 degree heat. Backed it in the garage and put my hand over the Vent and bam it was hot. I have a couple ideas that I did on my G8GT and it worked pretty well. Stand by as it involves moving some air. So, I just don't remember having that issue with my 16 ss with the two vent. I've been around this sport for years and thought I figured it all out but you just never know who can figure something else out that I didn't. Thx for passing that on, I looked at the seal at the cowl and that is more of a problem with the way the seal is attached, can't just pull it out or slid it out the other end.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
07-13-2022, 07:16 AM | #44 | |
Drives: 2021 LT1 10 speed auto Join Date: May 2013
Location: Connecticut
Posts: 2,344
|
Quote:
|
|
07-13-2022, 11:25 AM | #45 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
Let's say I've forgot a lot after 54 years of racing. I've had 6 years experience with this platform and the C7 platform. So just a little for sure.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
07-14-2022, 08:06 AM | #46 | |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
Quote:
Speed Engineering 1 7/8 long tubes, X-pipe, I loved my SE on my C7. Great sound and fit. I think we can get it deep in the 11s, probably 11.20s or teens. Still thinking about unleashing the trans and I think we could run in the 10s if we can work on the shifts, moving the RPMS up since we are on shifting at 6300 as we are limited to GMs stock trans tune.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
07-14-2022, 08:21 AM | #47 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,710
|
I’m really chomping at the bit for a trans tune. Would be really good if it picks up a couple tenths there
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
07-14-2022, 10:16 AM | #48 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
According to King about 3 tenths. Cost is about the same for me using the SE setup. I'm trying to remember if I'll need 02 extensions, I didn't on my C7 but don't remember on the Camaro
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
07-14-2022, 12:37 PM | #49 | |
Drives: 2021 LT1 10 speed auto Join Date: May 2013
Location: Connecticut
Posts: 2,344
|
Quote:
|
|
07-14-2022, 12:55 PM | #50 | |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
Quote:
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
07-14-2022, 02:40 PM | #51 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,710
|
I didn’t use any extension although it came with one
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
07-14-2022, 03:03 PM | #52 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
Ok thanks, got my order ready to go. I didn't recall on my 2016 SS if I used them or not.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
07-14-2022, 03:38 PM | #53 |
Drives: like an old lady Join Date: Jun 2012
Location: indiana
Posts: 2,455
|
i used an extension on one side. can't remember which. i think the drivers side..? i have another extension sitting around somewhere.
__________________
2016+ camaro: everyone’s first car
|
07-14-2022, 04:12 PM | #54 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,873
|
I'll just order them with all the other parts. Maybe I'll run across a deal on a blower over the winter. Right now I'm concentrating on getting ready for the LS Fest in September and the cool air in the fall to really dial it in. Its usually much cooler at the LS Fest then what we normally see here in June, July and August. Got my Hotel, Registration is done for Drag Racing and I'll be ready no matter how slow or fast I run.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
|
Post Reply
|
|
|