05-25-2024, 06:06 PM | #1 |
Drives: Zl1 Camaro Join Date: Oct 2023
Location: Wisconsin
Posts: 16
|
9.5 lower pulley
Is anyone running the iw lower pulley with a 9.5 ring from weapon x.
Thinking about doing this and keeping my upper pulley stock any thoughts or suggestions? |
05-25-2024, 08:24 PM | #2 |
Having FUN in the SUN...
Drives: 2022 M6 ZL1 1LE Join Date: Jan 2022
Location: San Diego CA
Posts: 1,195
|
I am not, but I see no issues with that. Thats an 18.75% OD for the record.
__________________
2022 M6 ZLE: Katech Standard Ported Blower + Ported Heads + 103mm TB + Oil Pump + C5R Chain + Valve Covers + Coil Relocation Kit
TSP VVT and DoD Delete Covers + LME Chain Guide + DSX Billet Lid + ATI Damper + 9.17" Lower + 2.4" Upper + MM Wild CC + RF BG Coated AR Headers + GESI UHO Cats + V Bands + AWE Touring + Magnaflow Center X + MSD Coils + Banks iDash + JMS Booster ALL the BMR Read End Goodies + BMR Motor Mounts + JRE Terminator Cam Package + FIC 30 + DMS Front HX + Fender Tank GMS High Flow Impact Bar + GMS Stage II Oil Cooler + GMS Stage III HX System = 770rwhp 815rwtq @E55 13.5psi |
05-28-2024, 05:11 PM | #3 |
Drives: Zl1 Camaro Join Date: Oct 2023
Location: Wisconsin
Posts: 16
|
Does anyone know what the supercharger rpms will be or the amount of boost?
|
05-28-2024, 07:13 PM | #4 |
Having FUN in the SUN...
Drives: 2022 M6 ZL1 1LE Join Date: Jan 2022
Location: San Diego CA
Posts: 1,195
|
At 6,700 rpm, the factory blower spins at approx. 21,440 rpm.
with a 9.5" lower, that will increase approx. 18.75% or 25,460 rpm. Your results will vary based on elevation and other mods... but you should be in the 11-12psi range. What else do you have done to the car?
__________________
2022 M6 ZLE: Katech Standard Ported Blower + Ported Heads + 103mm TB + Oil Pump + C5R Chain + Valve Covers + Coil Relocation Kit
TSP VVT and DoD Delete Covers + LME Chain Guide + DSX Billet Lid + ATI Damper + 9.17" Lower + 2.4" Upper + MM Wild CC + RF BG Coated AR Headers + GESI UHO Cats + V Bands + AWE Touring + Magnaflow Center X + MSD Coils + Banks iDash + JMS Booster ALL the BMR Read End Goodies + BMR Motor Mounts + JRE Terminator Cam Package + FIC 30 + DMS Front HX + Fender Tank GMS High Flow Impact Bar + GMS Stage II Oil Cooler + GMS Stage III HX System = 770rwhp 815rwtq @E55 13.5psi |
05-28-2024, 07:16 PM | #5 | |
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: Petersham MA
Posts: 5,122
|
Quote:
I wouldn’t buy anything from Weapon X… terrible company with non existent support.
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors, LPE BB HPFP, 15” conversion 1059 WHP/944 WTQ, 9.48@150
|
|
05-28-2024, 11:17 PM | #6 |
Drives: Zl1 Camaro Join Date: Oct 2023
Location: Wisconsin
Posts: 16
|
Will be doing a 103mm TB, 5” cold air, have kooks full 2” headers green cats and kooks mufflers then the lower pulley. Or would a smaller pulley be better?
|
05-29-2024, 06:51 AM | #7 |
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: Petersham MA
Posts: 5,122
|
Get the blower ported and add E before pulleys IMO.
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors, LPE BB HPFP, 15” conversion 1059 WHP/944 WTQ, 9.48@150
|
05-29-2024, 07:45 AM | #8 |
Snackbar Tuning
Drives: 2023 SGM ZL1 Join Date: Oct 2016
Location: Florida
Posts: 1,288
|
You're going to turn the blower into a furnace real quick and then power will drop considerably as the ECU pulls timing to keep the engine safe.
You're better off with Flex Fuel and a 2.3 upper. You really need some blend of E when you put a pulley on these cars.
__________________
GM Gen V Calibrator
|
05-29-2024, 07:52 AM | #9 |
Drives: 2016 1SS NFG A8 Join Date: Aug 2017
Location: 46804
Posts: 6,953
|
__________________
2016 NFG 1SS A8
Options-2SS Leather/NPP Perf. mods-Whipple 2.9/Fuel System/Flex Fuel/103mm TB/Rotofab Big Gulp/Cat Deletes/Corsa NPP Per. times- 10.5 @ 137 w/ 1.8 60ft Full weight on 20's 1200DA |
|
|
Post Reply
|
|
|