01-18-2024, 08:40 PM | #15 | ||
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 12,025
|
Quote:
Quote:
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
||
01-18-2024, 09:21 PM | #16 | |
Drives: 2020 Chevy Camaro ZL1 Join Date: Apr 2023
Location: Calgary Canada
Posts: 1,629
|
Quote:
|
|
01-19-2024, 02:23 PM | #17 |
Drives: Chevy Camaro Join Date: Nov 2021
Location: Indiana
Posts: 26
|
|
01-19-2024, 07:37 PM | #18 |
Drives: 2024 2SS vert w/M6 & Dual Mode. Red Join Date: May 2023
Location: NJ
Posts: 188
|
If you haven't already removed it, try this. Stack about a half dozen pieces of saturated Bounty paper towel that has a light film of dish detergent on the last one- smack on top the decal. Leave it wet and out of the sun for a day or two. Moisten with a spray water bottle if necessary. You should be able to scrape some or most off with your finger nails. (Really). That will guaranty no accidental glass damage. Place a dry, large, heavy bath towel just beneath the glass to keep the run off away from the soft top fabric.
|
01-19-2024, 09:39 PM | #19 |
Drives: Chevy camaro Join Date: Jan 2022
Location: Tennessee
Posts: 220
|
That's my plan, once the temperature warms up a bit. We've had lows down to 0.1°F to the mid 20's for the past couple of weeks here south of Nashville.
__________________
Glenn
2017 Camaro 2LT RS Convertible Last edited by truckrglenn; 01-19-2024 at 09:55 PM. |
01-19-2024, 10:02 PM | #20 |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 12,025
|
Next week we'll be good, I'm hoping for a few sunny days and mid-50s
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
01-20-2024, 05:43 PM | #21 |
Drives: '17 2SS convertible'20 Yukon Denali Join Date: Nov 2011
Location: Cedar Park, Texas
Posts: 2,955
|
I would be careful about using any type of chemical close to the edge of the glass. The window is glued to the top with an adhesive, which could be damaged by solvents. Many people have had problems with the adhesive getting bubbles and separating.
__________________
Richard
2017 2SS SIM convertible, A8, NPP, MRC, 56R wheels, GM CAI, Diode Dynamics Side Markers Delivered: 08/15/2016 #TeamBeckyD |
|
|
Post Reply
|
|
|