You are browsing camaro6 
10-23-2023, 03:12 PM
|
#1 |
          
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Shop Hours Edlebrock Install ?
Mine just broke so I've got to send it to Kong for repairs. How many shop hours are reasonable to pull it off the motor and pack it? And how many hours are reasonable for unpacking it and reinstalling it? I'm too old to even think of lifting that thing off and on the motor so my shop will do it.
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
10-23-2023, 05:04 PM
|
#2 |
Drives: 2017 Camaro ZL1 Coupe Join Date: May 2016
Location: Georgia
Posts: 5,875
|
Hard to say but it’s the hours the shop charges for labor. Good luck!
__________________
ZL1 Coupe, PDR, Exposed carbon fiber hood insert, My Link with Nav, M6 6 speed and Silver Ice Metallic. Mods done: ceramic window tint, GM Accessories Camaro floor mats and Roto-Fab CAI.
|
|
|
|
|
10-23-2023, 05:22 PM
|
#3 |
 Drives: 2022 Camaro ZL1 Join Date: Sep 2023
Location: Georgia
Posts: 54
|
10 hours.
|
|
|
|
|
10-23-2023, 05:32 PM
|
#4 |
|
Having FUN in the SUN...
 
Drives: 2022 M6 ZL1 1LE Join Date: Jan 2022
Location: San Diego CA
Posts: 2,189
|
Not sure about shop hours.
But, Had mine off a few times... For me, it would be off, and in the box in 2-3 hours +/- Careful install + HX bleeding would take about 4 hours +/-
__________________
2022 M6 ZLE: GMS Stage.III KONG X.PORT Package + DMS Lid + GMS Rear Bumper Belly Pan + GMS Hood Bracket + GMS Flex Fuel Package + MONSTER Triple S Clutch + XDI.50% Injectors + CLICK FOR BUILD LIST or www.GRIFFIN-MOTORSPORTS.com = 915rwhp 850rwtq + E60 + 15psi
|
|
|
|
|
10-23-2023, 05:49 PM
|
#5 | |
|
Moderator
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: New Ipswich NH
Posts: 6,350
|
Quote:
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, ATI 8L90, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors & BB HPFP, TooHighPSI/Katech port injection, 15” conversion 1066 WHP STD/1027 SAE, 9.10@152.5 (new times coming)
|
|
|
|
|
|
10-23-2023, 06:27 PM
|
#6 | |
|
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Quote:
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
|
|
10-24-2023, 07:01 AM
|
#7 | |
 
Drives: 2017 Chevrolet Camaro ZL1 Join Date: Jul 2018
Location: Canton, GA
Posts: 475
|
Quote:
__________________
2017 ZL1 - PB 7.85 @ 175 MPH @ 3682 lbs @ 1313 DA (work in progress)
Built by Vengeance Racing, tuned by Elite Tuned |
|
|
|
|
|
10-24-2023, 09:05 AM
|
#8 | |
|
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Quote:
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
|
|
10-28-2023, 03:11 PM
|
#9 |
|
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
It took two hours to pull the inlet, hoses, TB, Eddie, valve covers, turn it over and look in cylinders, poke around, and put it all back together. We did not find a problem except it looks as if the bottom pulley is wobbling a bit. Shop wants to drop and take the engine apart and do oil pump, thrust bearing, etc.
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq Last edited by JSH; 10-28-2023 at 04:44 PM. |
|
|
|
|
|
|
|
|
Post Reply
|
| Thread Tools | |
|
|
