You are browsing camaro6 
08-03-2019, 10:18 AM
|
#1 |
 Drives: 64vette,2010 2SS,2013 Zl1 Join Date: Mar 2013
Location: kanata,on,can.
Posts: 89
|
ZL1 addons
I just got my 2019 zl1 and I got some zl1 addons to facilitate jacking the car but something I'm not sure of, the slot in the addons where the weld fit into is deeper than the weld so when jacking, the whole pressure is on the floor on each side of the weld and none on the weld itself, is that the way it's suppose to be.
64stingray |
|
|
|
08-03-2019, 10:28 AM
|
#2 |
 |
Yes, along as you have them where they're supposed to you'll be fine.
|
|
|
|
|
08-03-2019, 11:08 AM
|
#3 |
    
Drives: 2019 ZL-1, Shadow Gray, Sold Join Date: Jan 2019
Location: Fredericksburg, VA
Posts: 1,390
|
Yep.
|
|
|
|
|
08-03-2019, 11:22 AM
|
#4 |
   
Drives: 2019 Silverado Z71 6.2L A10 Join Date: Mar 2017
Location: Grapevine
Posts: 2,075
|
I bought them but have not used them yet. I was thinking on leaving them on all the time, but my luck I would lose one.
__________________
Current ride
2019 Silverado Z71 LTZ 6.2L L87 425hp A10, 4 inch BDS Lift with Fox Factory Race 2.5 Coilovers, Borla Cat back (15HP bump), BFG KM3's 33's. Past Rides 2017 M6 Camaro ZL1 Hyper Blue 2016 M6 GT350 White with blue strips 2014 M6 Mustang GT Premium Track Pack Ruby Red 2012 M6 M3 Melbourne Red Metallic |
|
|
|
|
08-03-2019, 11:27 AM
|
#5 |
|
To fast is not enough
Drives: 2019 ZL1 Camaro & 2020 CT5-V Turbo Join Date: May 2019
Location: NC
Posts: 85
|
I put them on and so far they stayed. 6 months now.
|
|
|
|
|
08-03-2019, 11:28 AM
|
#6 | |
 
Drives: 2017 Summit White ZL1 M6 Join Date: May 2017
Location: B'ham AL
Posts: 189
|
Quote:
I have had mine on for two years and 11K miles and had no issue with one or more coming off. I check the set screws from time to time but they are never loose.
__________________
Roto Fab/ Kook's LT's,ported blower,removed lid baffle/ 103mm TB' lower pulley and tune.
651/660. |
|
|
|
|
|
08-03-2019, 12:46 PM
|
#7 |
|
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
Had mine for 4K miles and used them several times with no issues. I do check if they are loose every time tho. I’ve only retorqued once after driving the car about 10 miles with them on just to be safe.
|
|
|
|
|
08-03-2019, 02:12 PM
|
#8 | ||
Drives: 2016 Camaro 2SS Join Date: Jun 2016
Location: Maryland
Posts: 810
|
Quote:
|
||
|
|
|
|
08-03-2019, 02:46 PM
|
#9 |
Drives: 2018 Camaro ZL1 Summit White Join Date: Apr 2018
Location: Ketchikan, AK
Posts: 49
|
Mine have been on since day 1 , April of 2018.
I did put a little dab of blue loctite on the set screws and have not had to tighten them or touch them. Hope that helps. |
|
|
|
|
08-03-2019, 03:09 PM
|
#10 |
|
CamaroFans.com
|
I just use the magnetic one with puck.
It lifts both front and rear tires at the same time.
__________________
 |
|
|
|
|
08-03-2019, 04:01 PM
|
#11 |
|
Drives: 2019 ZL-1, Shadow Gray, Sold Join Date: Jan 2019
Location: Fredericksburg, VA
Posts: 1,390
|
Blue Loctite on my set screws as well, and have not any retighten issues.
|
|
|
|
|
|
|
|
|
Post Reply
|
| Thread Tools | |
|
|
