JMS Boost-a-pump Install - Page 2

L78toLT1 · 05-04-2019, 12:22 PM

Thanks guys. Those look like two good options. If i didn't have a cookout to go to this afternoon, I'd go out to the shop and knock this out. I've also got a catch csn that's been l aying around a month or so, waiting to get installed.

TJay74 · 05-06-2019, 09:44 AM

Mine is mounted similar to their, except for it is on the floor of that area in the side compartment since I have a JL Audio stealth box that mounts to that brace.

I used Gorilla duct tape to secure mine, that stuff is insane. The JMS doesnt move one bit at all.

Epx998 · 05-06-2019, 12:10 PM

Great info in the replies!

Burntblues · 03-22-2025, 07:08 PM

I know this is a super old thread but how did you guys run the cables from the box to the gas pedal. Do you have to remove the rear seat and the rear sail panel

SWFLZL1 · 03-23-2025, 09:41 AM

Quote:

Originally Posted by Burntblues

I know this is a super old thread but how did you guys run the cables from the box to the gas pedal. Do you have to remove the rear seat and the rear sail panel

I folded back seat down, and removed the trunk panels of course, and also the sill plate on drivers side. I was able to run a fish tape through and behind the drivers side interior quarter piece, and then pull the wire through. Only took a few minutes and avoided damaging any plastic pieces by not removing them.

05-04-2019, 12:22 PM	#15
L78toLT1 Drives: Hyper Blue 2016 2SS 6M Join Date: Sep 2017 Location: North Ga Posts: 1,810	Thanks guys. Those look like two good options. If i didn't have a cookout to go to this afternoon, I'd go out to the shop and knock this out. I've also got a catch csn that's been l aying around a month or so, waiting to get installed. __________________ Baby Blue 2016 Hyper Blue 2SS/6m/MRC/NPP/Silver Rally stripes/ZL1 wheels & brakes/GForce DS and axles/ZLE Cradle Bushings/FE4 ARB front & rear/SEMA Grill/Rotofab dry/95mm TB/Magnuson 2300/Full LT4 fuel system/JMS boost-a-pump/E85 Sensor/Ported CID heads from LME/Cammotion PD cam/Thompson Motorsports forged shortblock/catted Kooks 1 7/8 headers /JRE remote tuned

05-06-2019, 09:44 AM	#16
TJay74 Drives: 17 Camaro SS 1LE & 16 Sierra AT CC Join Date: Nov 2016 Location: Norman, OK Posts: 2,424	Mine is mounted similar to their, except for it is on the floor of that area in the side compartment since I have a JL Audio stealth box that mounts to that brace. I used Gorilla duct tape to secure mine, that stuff is insane. The JMS doesnt move one bit at all. __________________ 2019 Corvette Z06 2LZ A8 - Halltech CAI, AWE non-catted X-pipe, Mamo V2 ported TB 592rwhp, bone stock 566rwhp 2017 Camaro SS 1LE - Procharger D1SC w/ Tial 2" BOV & Race intercooler / ARH full length catless headers / Alky meth injection system - 650rwhp on conservative tune SOLD

05-06-2019, 12:10 PM	#17
Epx998 \|Engineer\| Drives: 2016 Camaro SS Join Date: Aug 2016 Location: San Jose, CA Posts: 402	Great info in the replies! __________________ 2016 Camaro SS A8 \| Magnuson Heartbeat \| Might Mouse Wild Catch Can \| DSX Flex Fuel \| Eibach Pro Kit \| Flowmaster Outlaw Black Series \| MRR 017 Wheels

03-22-2025, 07:08 PM	#18
Burntblues Drives: 2017 ZL1: 1989 Camaro Join Date: Dec 2018 Location: North Carolina Posts: 3	I know this is a super old thread but how did you guys run the cables from the box to the gas pedal. Do you have to remove the rear seat and the rear sail panel

User Name		Remember Me?
Password