You are browsing camaro6 
11-19-2018, 01:35 AM
|
#1 |
 
Drives: 2016 ss camaro Join Date: Jan 2018
Location: Bellflower ca
Posts: 199
|
Msd 2 Step
Hello all,
Has anyone had a chance to install an msd 2 step. I'm in the middle of installing mine, but the instructions are rather vague. I'm trying to connect it, at the clutch pedal. There is 3 wires at the clutch pedal, None are 12 volts? I tried the middle wire (yellow) as i read on here that another member used that one, but it actually turns off the box when i press the clutch in, vs engaging the box! Hit a wall on this one, any ideas? 
__________________
Last edited by Buckscamaro; 11-19-2018 at 01:37 AM. Reason: typos |
|
|
|
11-19-2018, 06:21 AM
|
#2 |
  
Drives: '17 Red hot 2ss, 16 Focus RS Join Date: Aug 2015
Location: Michigan
Posts: 845
|
I think you need a window switch to be able to use the clutch because it's a clutch position sensor, instead of just the on/off style sensor older cars had.
__________________
"Spitfire" 427ci
2017 Red Hot 2SS// 6 Piston Brembos//Adrenaline Red Interior, Knee Pads//M6//MRC Afe Air Filter//BMR MM010 Motor Mounts, Safety Loop//Custom OTR Intake//Flex Fuel Kit//Gforce 3.5" Aluminum Driveshaft//GM 95mm TB//Katech Oil Pump, Piston Squirters//Kooks 1-7/8 LT//LT4 Fueling//Mighty Mouse Wild//Monster Clutch LT1-S Triple Disc//MSD 2-Step//Pray Performance Custom Spec Cam, Ported Holley Hi-Ram//Sikky 12" Shifter w OEM Knob Mod//Tick Level 1 Tr6060//Labor by Me//Tune By Pray Performance |
|
|
|
|
11-19-2018, 07:08 PM
|
#3 |
|
Drives: 2016 ss camaro Join Date: Jan 2018
Location: Bellflower ca
Posts: 199
|
Ok guys I was able to make it work. Forum member Est98ss told me how he wired it! You need to wire it opposite of what the msd instruction say and add a toggle switch;that’s the trick. Or else car won’t read the clutch pedal signal when you go to start it again! So basically, hook up to 12v, add a switch to shut it off before you start the car! And tap in to yellow wire at clutch pedal plug.
Thanks est98ss
__________________
|
|
|
|
|
11-27-2018, 11:54 AM
|
#4 |
|
Drives: 2017 Camaro SS 2ss Nightfall Gray Join Date: Aug 2018
Location: New york
Posts: 149
|
Does the msd work much better than the factory launch control?
__________________
ACS front spoiler, rear spoiler, side skirts and rock guards (gloss black). Real carbon fiber dash insert, real carbon fiber gear bezel, GM dark tail lights, Gm black badges(Emblems and ss)
Powder-coated gloss black factory 5 spoke split wheels Roto fab Biggulp CAI Full paint correction with cquartz finest ceramic coating Whipple 2.9 ARH Long tube headers with High flow cats 1le sway bars F&R BMR Upper and lower trailing arms Hurst short throw shifter |
|
|
|
|
11-27-2018, 06:03 PM
|
#5 |
|
Drives: 2016 ss camaro Join Date: Jan 2018
Location: Bellflower ca
Posts: 199
|
Tbh I’ve never really used the stock one! I just wanted the 2 step to be able to play with the rpms, and set it specifically to certain rpm when testing mods. I was all over the place trying to hold my launch at 4,200. I believe the stock launch control is around 3500 but don’t quote me on it, I may be wrong as I’ve never used it.
__________________
|
|
|
|
|
11-28-2018, 12:45 PM
|
#6 |
|
Drives: 2016 ss camaro Join Date: Jan 2018
Location: Bellflower ca
Posts: 199
|
__________________
|
|
|
|
|
11-28-2018, 04:51 PM
|
#7 |
   Drives: 17 SS a8 Join Date: Feb 2010
Location: omaha
Posts: 1,678
|
Nice! I hope to be hooking up a 2 step soon.
At some point I think I had a backfire that bent both my npp valves. I wouldn’t be suprized if 2stepping it with the valves closed bent the valves.
__________________
dropped a valve in the 6.2. now running a drop in rods and piston 5.3
best et 5.83@121 with the 5.3 http://www.camaro6.com/forums/showthread.php?t=465472 |
|
|
|
|
11-28-2018, 07:57 PM
|
#8 | |
|
Drives: 2016 ss camaro Join Date: Jan 2018
Location: Bellflower ca
Posts: 199
|
Quote:
__________________
|
|
|
|
|
|
|
|
|
|
Post Reply
|
| Thread Tools | |
|
|
