Twin turbo build 6766s - Page 2

Turbo_RORO · 04-23-2018, 08:29 AM

Quote:

Originally Posted by parish8

I didn’t know they had a larger vband set up. I might have to change my set up to accept those if I get to the point I need the 67’s

I think the small exhaust housing 62’s will take me to 1200rwhp. I am sure I will have many issues to work through before I can use all that power effectively.

Yeah they just dropped early April. They are a 1.05 stainless housing. I wish they were out a few days earlier. When I spoke with the guys at Precision they thought the .81 v bands would really shine around 1000 but would max around 1100. I'm not sure but they should be pretty close to drop in for your setup.

parish8 · 04-23-2018, 10:34 AM

Quote:

Originally Posted by Turbo_RORO

Yeah they just dropped early April. They are a 1.05 stainless housing. I wish they were out a few days earlier. When I spoke with the guys at Precision they thought the .81 v bands would really shine around 1000 but would max around 1100. I'm not sure but they should be pretty close to drop in for your setup.

I just called precision. The lady told me the 1.05 stainless vband inlet ex housing is a direct replacement for the .82 that I have now. That means it is still t3 based and probabily not ideal for a max effort build but still an improvement over what I have now. If I ever step up to 67’s I will go with them.

She did suggest I monitor my exhaust pressure so I know if the .82’s are hurting me. Seems like good advice.

Turbo_RORO · 04-23-2018, 08:26 PM

Quote:

Originally Posted by parish8

I just called precision. The lady told me the 1.05 stainless vband inlet ex housing is a direct replacement for the .82 that I have now. That means it is still t3 based and probabily not ideal for a max effort build but still an improvement over what I have now. If I ever step up to 67’s I will go with them.

She did suggest I monitor my exhaust pressure so I know if the .82’s are hurting me. Seems like good advice.

I thought it was still a T3 housing. Do you have an exhaust pressure setup currently? I talked to Goertz briefly about one a while ago.

Turbo_RORO · 04-23-2018, 08:48 PM

Here are a couple pics. The first is a pic of the Motion Raceworks header build kit. 1.75 inch tubes and 2.5 inch collector. Name: 20180406_162505.jpg
Views: 654
Size: 138.0 KB

Name: 20180406_162505.jpg
Views: 654
Size: 138.0 KB

Turbo_RORO · 04-23-2018, 08:52 PM

Headers coming along...kinda. But should be finished tomorrow. I really like welding Stainless steel. To me it is much easier than aluminum but aluminum is not bad though.

Turbo_RORO · 04-23-2018, 08:54 PM

And a couple turbo shots.

laynlo15 · 04-23-2018, 08:56 PM

There are lots of tubes to have fun with.

Turbo_RORO · 04-23-2018, 10:08 PM

Quote:

Originally Posted by laynlo15

There are lots of tubes to have fun with.

Yeah. I ordered a couple extra bends for the headers just in case. The others are for the wastegate charge and discharge, and turbo charge. Luckily I didn't need them yet. I'll be done with them tomorrow.

Turbo_RORO · 04-24-2018, 07:19 PM

Getting close. Just ran out of argon. Back purging is a bottle killer. But I was able to get measurements to make my input pipes and the rest of the hot side!

Turbo_RORO · 04-24-2018, 08:06 PM

Started fitting the intercooler. This big beast takes up a lot of room. 18x14x6 she gonna flow.

Rlhay2 · 04-25-2018, 11:09 AM

Glad to see a FMIC being installed. I've always though the 6th gen ZL1 front bumper was just an invitation for just such a design!

Looking forward to the results.

Turbo_RORO · 04-25-2018, 06:22 PM

Quote:

Originally Posted by Rlhay2

Glad to see a FMIC being installed. I've always though the 6th gen ZL1 front bumper was just an invitation for just such a design!

Looking forward to the results.

Thanks, but this is just a lowly old SS. But I like the front mount stuff may do air to water if air to air doesn't work out as I'd like.

Turbo_RORO · 04-25-2018, 06:26 PM

Headers fit nice... now on to turbo mounts.

jhempsrt4 · 05-19-2018, 10:02 PM

Any update?

04-23-2018, 08:52 PM	#19
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	Headers coming along...kinda. But should be finished tomorrow. I really like welding Stainless steel. To me it is much easier than aluminum but aluminum is not bad though. Attached Images

04-23-2018, 08:54 PM	#20
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	And a couple turbo shots. Attached Images

04-24-2018, 07:19 PM	#23
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	Getting close. Just ran out of argon. Back purging is a bottle killer. But I was able to get measurements to make my input pipes and the rest of the hot side! Attached Images

04-24-2018, 08:06 PM	#24
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	Started fitting the intercooler. This big beast takes up a lot of room. 18x14x6 she gonna flow. Attached Images

04-25-2018, 06:26 PM	#27
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	Headers fit nice... now on to turbo mounts. Attached Images

04-23-2018, 08:48 PM	#18
Turbo_RORO Drives: Camaro 17 SS Join Date: Jan 2017 Location: Florida Posts: 623	Here are a couple pics. The first is a pic of the Motion Raceworks header build kit. 1.75 inch tubes and 2.5 inch collector.

04-23-2018, 08:56 PM	#21
laynlo15 Drives: 2022 Lt1 A10 Join Date: Nov 2015 Location: clark, mo Posts: 8,882	There are lots of tubes to have fun with.

04-25-2018, 11:09 AM	#25
Rlhay2 Drives: 2017 ZL1 Join Date: Mar 2014 Location: DFW, TX Posts: 310	Glad to see a FMIC being installed. I've always though the 6th gen ZL1 front bumper was just an invitation for just such a design! Looking forward to the results.

05-19-2018, 10:02 PM	#28
jhempsrt4 Drives: braaaaap Join Date: Jan 2011 Location: Indiana Posts: 38	Any update?

User Name		Remember Me?
Password