Adhesive remover for wheel weight goo

VinnAY · 05-13-2019, 02:06 PM

Can you recommend a solid product to get the goo off without paint damage to the wheel? I had my A/S and summers swapped out and of course there was a weight change on one wheel the they left the adhesive backing from the old weights. I wouldn't presume that basic Goo-Gone is going to get the job done here.

Edit: WD-40, perhaps?

KirkH · 05-13-2019, 02:41 PM

Quote:

Originally Posted by VinnAY

Can you recommend a solid product to get the goo off without paint damage to the wheel? I had my A/S and summers swapped out and of course there was a weight change on one wheel the they left the adhesive backing from the old weights. I wouldn't presume that basic Goo-Gone is going to get the job done here.

Edit: WD-40, perhaps?

Start with Goo Gone. There are several types. Automotive is the one I'd start with. Let it soak. Use a plastic scraper tool.

Next, I go to Turtle Wax Label & Sticker Remover. It's a little stronger and gets almost everything off.

Then Stoner Tarminator Tar and Sap Remover. Much stronger, use gloves. Again plastic scraper tool.

One of those will get it off.

VinnAY · 05-13-2019, 03:24 PM

Gracias...will play around with it tonite, unfortunately will have to jack and pull the wheel in order to make an attempt at it, not acceptable installed but I may try that before jacking.

KirkH · 05-13-2019, 03:44 PM

Quote:

Originally Posted by VinnAY

Gracias...will play around with it tonite, unfortunately will have to jack and pull the wheel in order to make an attempt at it, not acceptable installed but I may try that before jacking.

Heres my thread on full wheel detail off the car:

https://www.camaro6.com/forums/showt...l+wheel+detail

F419sr1 · 05-13-2019, 04:25 PM

Quote:

Originally Posted by KirkH

Heres my thread on full wheel detail off the car:

https://www.camaro6.com/forums/showt...l+wheel+detail

Thanks for the info

bobby35ny · 05-13-2019, 04:39 PM

plastic razor blades...

solvent of your choice
thank me later

warren3537 · 05-13-2019, 04:56 PM

CarPro Tar-X works great with any adhesive based products, or get a rubber wheel and it won't tear up the paint

VinnAY · 05-13-2019, 08:25 PM

I found some similar to goo-gone orange product and as it turn's out it worked pretty well with not much elbow grease and a rag. soak, let it sit, rub, worked OK for what I needed.

driven2exceSS · 05-14-2019, 10:42 AM

Quote:

Originally Posted by VinnAY

I found some similar to goo-gone orange product and as it turn's out it worked pretty well with not much elbow grease and a rag. soak, let it sit, rub, worked OK for what I needed.

Little late to the game here, but this stuff is awesome!!!

KirkH · 05-14-2019, 11:30 AM

Quote:

Originally Posted by driven2exceSS

Little late to the game here, but this stuff is awesome!!!

I have a Malco account and use several of their products, but that product has a big warning on it for causing cancer so be careful with that one!

driven2exceSS · 05-14-2019, 07:36 PM

Thanks for the heads up

VinnAY · 05-15-2019, 07:53 AM

ah yes Cosmoline...you guys familiar with that product? I can still smell it...from being a prior collector of surplus firearms from Eastern Europe, cosmoline is just plain nasty to clean out of a rifle. Used as a storage preservative/protectant.

driven2exceSS · 05-15-2019, 08:28 AM

Quote:

Originally Posted by VinnAY

ah yes Cosmoline...you guys familiar with that product? I can still smell it...from being a prior collector of surplus firearms from Eastern Europe, cosmoline is just plain nasty to clean out of a rifle. Used as a storage preservative/protectant.

Not too familiar, but have been using it here and there since going to the NAPA dealer that carried the product line to find something that WILL work on the residue after removing the sun visor warming decals. Kirk is much more in tune, I'm not a detailer or anything close. But I did just use it for the very purpose of the wheel weight goo

KirkH · 05-15-2019, 09:07 AM

Quote:

Originally Posted by driven2exceSS

Not too familiar, but have been using it here and there since going to the NAPA dealer that carried the product line to find something that WILL work on the residue after removing the sun visor warming decals. Kirk is much more in tune, I'm not a detailer or anything close. But I did just use it for the very purpose of the wheel weight goo

Malco makes good products that work. I am just up to my elbows in the chemicals every day so i try to avoid the ones that have cancer warnings.

05-13-2019, 02:06 PM	#1
VinnAY Account Suspended Drives: 18 1SS/1LE Join Date: Jun 2018 Location: Missouri Posts: 939	Adhesive remover for wheel weight goo Can you recommend a solid product to get the goo off without paint damage to the wheel? I had my A/S and summers swapped out and of course there was a weight change on one wheel the they left the adhesive backing from the old weights. I wouldn't presume that basic Goo-Gone is going to get the job done here. Edit: WD-40, perhaps?

05-13-2019, 04:39 PM	#6
bobby35ny Drives: 18 ZL1 A10 Join Date: Nov 2008 Location: South East, FL Posts: 3,023	plastic razor blades... solvent of your choice thank me later __________________ 2017 ZL1 M6 Bog City, 2013 ZL1 M6, 2010 2SS M6 ZL1::J-E-T-S JETS JETS JETS

05-14-2019, 07:36 PM	#11
driven2exceSS Drives: 2016 2SS BLK A8 Vert Join Date: Dec 2017 Location: MA Posts: 1,040	Thanks for the heads up __________________ NPP, MRC, Tinted side & rear reflectors, OEM ZL1 Rockers / 3rd Brake / Darken tail lights, OEM Blk rear splash guards, Satin hood wrap, Fuse pull, Sound tube delete, Cat delete, Ported 95 TB, Ported MSD IM, Dry RotoFab, ARH 1 7/8 headers, E85, "Performance Dyno" Tune, BMR "pieces", "Track" alignment, Hawk DCT-70/70's w/SRF, Goodridge lines, Ti shims, Red powdered calipers, 18" APEX SM-10's w/ Pirelli DH's, FE4 Vert swaybars, Brake cooling ducts, ATI 10% UD, Vorshlag camber plates, OEM 1LE Splitter w/APR Ext., Velossa BIG MOUTH Ram Air, CF QA1, ZLE brakes(F)

05-13-2019, 03:24 PM	#3
VinnAY Account Suspended Drives: 18 1SS/1LE Join Date: Jun 2018 Location: Missouri Posts: 939	Gracias...will play around with it tonite, unfortunately will have to jack and pull the wheel in order to make an attempt at it, not acceptable installed but I may try that before jacking.

05-13-2019, 04:56 PM	#7
warren3537 Drives: 2019 Red Hot ZL1 1LE: 2012 RAM 2500 Join Date: Mar 2012 Location: DeRidder, LA Posts: 711	CarPro Tar-X works great with any adhesive based products, or get a rubber wheel and it won't tear up the paint

05-13-2019, 08:25 PM	#8
VinnAY Account Suspended Drives: 18 1SS/1LE Join Date: Jun 2018 Location: Missouri Posts: 939	I found some similar to goo-gone orange product and as it turn's out it worked pretty well with not much elbow grease and a rag. soak, let it sit, rub, worked OK for what I needed.

05-15-2019, 07:53 AM	#12
VinnAY Account Suspended Drives: 18 1SS/1LE Join Date: Jun 2018 Location: Missouri Posts: 939	ah yes Cosmoline...you guys familiar with that product? I can still smell it...from being a prior collector of surplus firearms from Eastern Europe, cosmoline is just plain nasty to clean out of a rifle. Used as a storage preservative/protectant.

User Name		Remember Me?
Password