You are browsing camaro6 
06-20-2018, 07:06 PM
|
#1 |
           
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,069
|
ARH NPP mufflers
I just bought a set of Hurst branded Flowmaster NPP mufflers to go with my ARH long system so ARH should be coming out with a set of their own NPP mufflers any day now
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
|
|
|
06-20-2018, 07:17 PM
|
#2 |
|
SS Copbait R.I.
Drives: 2016 Camaro 2SS Join Date: Dec 2016
Location: Aquidneck island
Posts: 217
|
Nice, where did you buy them from? How much?
|
|
|
|
|
06-20-2018, 07:26 PM
|
#3 |
|
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,069
|
http://www.hurst-shifters.com/produc...d=492&eng=5920 they are Flowmasters just wit hthe Hurst logo on them.
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
|
|
|
|
06-20-2018, 07:34 PM
|
#4 |
|
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,069
|
ill take some pics of the logo tomorrow after install. dont want to take the foam off the tips until there on the car. Unfortunately the the ARH pipe is 3" and the 2.75" factory muffler goes in side it. On these mufflers they are 3" and suppose to go over the factory 2.75" pipe. So both pipes are 3" so ill have to get the ARH pipe stretched to go over the mufflers.
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
|
|
|
|
06-22-2018, 12:21 AM
|
#5 |
|
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,069
|
well to fit it to the ARH pipes it had to be welded on an the muffler pipe needed to be cut. because of the hangers the tips sit to far in to see the Hurst on the tips and i didnt take pics befor they were put on because they were wrapped in foam. They are louder then the stock NPP with the valves closed but not bad. Valves open is about the same as strait pipes. IT LOUD. but no bad drone. no annoying drone at cruise. In stealth mode the valved rattle quite a bit under moderate throttle were the valves would normally open but they dont at cruise or when open. over all im happy with it.
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
|
|
|
|
|
|
|
|
Post Reply
|
|
|
