CAMARO6 - View Single Post

travislambert · 10-08-2016, 11:45 AM

A member asked me to post part #s so here it goes....

Keep in mind many of the '17 ZL1 parts were not available at the time I did my build so there might be more ideal parts available now. Also, I ordered my engine with the s/c belt, pulleys, heat exchanger, and supercharger inlet duct so unfortunately I don't have the numbers for these. Contact Greg Was at pace performance (gregwas@paceperformance.com) if you need these parts. Pace Performance is a GM parts dealer that sells parts as cheap as you'll find anywhere. (I am in no way affiliated with pace performance. I'm simply a happy customer.)

19332621 - LT4 Crate Engine (Wet Sump) - It comes with a very good intercooler pump (13597903). It also comes with the knock sensor heat shield it claims not to come with.
23117748 - LT4 Fuel line (Comes with plastic clips)
23455459 & 23455460 - Heat Exchanger Brackets (Left & Right, but I'm not sure which is which)
11570323 - Heat Exchanger Bracket Bolt - $3.66 each (x8)
23377187 - Brake booster vacuum line - This part doesn't actually fit, but you can use the connectors on it to make one that does.
13584423 - MAP Connector Pigtail - Some folks simply swap for an LS9 MAP without the IAT2. I bought this connector instead and ran a new wire for the IAT2 to the ECM.
12663963 - Evap Tube
84013640 - '17 ZL1 Radiator Hose Assembly - You can make the SS one work. There's not much difference, but it was worth the money to me to not have to fool with it.
12561465 - Clutch Pressure Plate Bolts - $.59 ea - (x6)
24268307 - '16 Z06 Clutch & Pressure Plate - $343.18
24255997 - '16 Z06 Flywheel - $601.03 (Same part # as '16 Camaro SS Flywheel) This comes with flywheel bolts.
12563485 - Flywheel bolts - $5.80 ea (x8) You'll need these if you are reusing your LT1 flywheel. Do not reuse the old bolts! They stretch when torqued.
12624939 - Exhaust Manifold to converter gasket - $7.36 x2
21992620 - Exhaust gasket (after passenger side converter) - $16.36 ea
12557583 - GM Roller Pilot Bearing - $11.34
19300589 - Coolant Pump Connector Pigtail - $50.32
12647125 - PCV hose
23385107 - Engine Wiring Harness for Camaro SS Manual with Magnetic Ride Control - $330.65
88988501 - Supercharger Bypass Connector Pigtail - $16.91
23296636 - Intercooler Hose
23424016 - Radiator Hose (Don't remember where this one goes)
11589264 - 2016 Camaro SS Exhaust manifold studs - $8.05 each. (x8) These can be reused, but are sometimes hard to remove so I just bought new ones.

Misc parts I ordered for intercooler plumbing
-----------------------------------------------
12670874 - Tube - $32.10
23424013 - Hose - $20.65
23424015 - Fitting - $32.99
11547667 - Hose Clamp - $2.40 (x3)
11570871 - Hose Clamp - $3.23 (x2)
11519385 - Bolt - $2.87 (x2)

Other stuff you'll probably need
--------------------------------
- Tesa 50126 Wiring Harness Tape (2 rolls should do fine) https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

- Heat Exchanger

- ZL1 Jack Pads from https://www.zl1addons.com. I would buy 4 with the jack pads if you plan to use a lift. They're worth the money.

- PF64 Oil Filter and 11 quarts of oil (The first fill takes a little more than 10 quarts).

- A fused relay, wiring, and loom for the coolant pump. I used the Painless Wiring 30821 Hlite Relay Kit #37827 and modified it to work like a normal relay.

- Dexcool Coolant (2 gallons of concentrate and 2 gallons of distilled water will be plenty.)

- Fir Tree Push Mount cable ties. I used these: https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

- A set of Push type retainer clips. The Swordfish 60010 kit has ones that match GM perfectly. https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

- Loctite 242 and 272... A tiny bottle of each will work fine.

- A/C Vacuum Pump kit to recharge A/C System. I bought these and they worked great:

FJC (6909) 3.0 CFM Vacuum Pump - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
Mountain 8205 R-134a Brass Manifold Gauge Set with Couplers - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
Mountain 8401 Top Style Metal Can Tap - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1
ACDelco 10-9097 R134A (I think you need 2 cans. I would get 3 just to be sure.) - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

- 19299818 - Brake and Clutch Fluid (FYI, to bleed the clutch on these you'll probably need to put a vacuum pump on the brake fluid reservoir. The bleeder is pretty much impossible to get to after the transmission is put back into the car.)

- Lots of time

Other Misc Stuff That You Probably Won't need
--------------------------------------
52474373 - A/C Compressor Seal - $4.20
12657093 - GM LT1, L83, L86 Exhaust Manifold Gasket - $4.03
11546600 - Exhaust manifold to engine bolt - $2.69 ea (x10)
11611992 - Supercharger lid bolt - $2.45
84044721 - Underhood fuse block (LT1) - $143.86
84063674 & 84063675 - Rear '17 SS 1LE Calipers - $240.00 each
12672471 - PCV Oil Separator - $80.04
12657430 - Water Manifold Gaskets - $2.48 ea (x2.)
12656725 - Engine Oil Cooler Line (Runs from the bottom of the water manifold to the rear of the engine oil cooler) - $50.42
23355791 – '17 SS 1LE Front Wheels 20 x 10 - $572.40 plus $50.00 core charge
23355802 - '17 SS 1LE Rear Wheels 20 x 11 - - $572.40 plus $50.00 core charge
23115614 - '17 SS 1LE Wheel Center Cap - $20.99 (x4)
13598786 (RPO code XL7 315mHz) or 13598787 (RPO code XL8 433mHz) - TPMS Sensor - $45.64 (x4)
24274085 - Clutch Slave Cylinder - $310.07
12644807 - LT4 MAP Sensor (just in case your engine comes with the wrong one like mine did)
12640390 - Knock Sensor Shield - $19.18 (The LT4 docs say you need to buy this, but mine came with it.)

10-08-2016, 11:45 AM	#46
travislambert Drives: '17 ZL1 Join Date: Jul 2016 Location: Fairmont, WV Posts: 1,558	A member asked me to post part #s so here it goes.... Keep in mind many of the '17 ZL1 parts were not available at the time I did my build so there might be more ideal parts available now. Also, I ordered my engine with the s/c belt, pulleys, heat exchanger, and supercharger inlet duct so unfortunately I don't have the numbers for these. Contact Greg Was at pace performance (gregwas@paceperformance.com) if you need these parts. Pace Performance is a GM parts dealer that sells parts as cheap as you'll find anywhere. (I am in no way affiliated with pace performance. I'm simply a happy customer.) 19332621 - LT4 Crate Engine (Wet Sump) - It comes with a very good intercooler pump (13597903). It also comes with the knock sensor heat shield it claims not to come with. 23117748 - LT4 Fuel line (Comes with plastic clips) 23455459 & 23455460 - Heat Exchanger Brackets (Left & Right, but I'm not sure which is which) 11570323 - Heat Exchanger Bracket Bolt - $3.66 each (x8) 23377187 - Brake booster vacuum line - This part doesn't actually fit, but you can use the connectors on it to make one that does. 13584423 - MAP Connector Pigtail - Some folks simply swap for an LS9 MAP without the IAT2. I bought this connector instead and ran a new wire for the IAT2 to the ECM. 12663963 - Evap Tube 84013640 - '17 ZL1 Radiator Hose Assembly - You can make the SS one work. There's not much difference, but it was worth the money to me to not have to fool with it. 12561465 - Clutch Pressure Plate Bolts - $.59 ea - (x6) 24268307 - '16 Z06 Clutch & Pressure Plate - $343.18 24255997 - '16 Z06 Flywheel - $601.03 (Same part # as '16 Camaro SS Flywheel) This comes with flywheel bolts. 12563485 - Flywheel bolts - $5.80 ea (x8) You'll need these if you are reusing your LT1 flywheel. Do not reuse the old bolts! They stretch when torqued. 12624939 - Exhaust Manifold to converter gasket - $7.36 x2 21992620 - Exhaust gasket (after passenger side converter) - $16.36 ea 12557583 - GM Roller Pilot Bearing - $11.34 19300589 - Coolant Pump Connector Pigtail - $50.32 12647125 - PCV hose 23385107 - Engine Wiring Harness for Camaro SS Manual with Magnetic Ride Control - $330.65 88988501 - Supercharger Bypass Connector Pigtail - $16.91 23296636 - Intercooler Hose 23424016 - Radiator Hose (Don't remember where this one goes) 11589264 - 2016 Camaro SS Exhaust manifold studs - $8.05 each. (x8) These can be reused, but are sometimes hard to remove so I just bought new ones. Misc parts I ordered for intercooler plumbing ----------------------------------------------- 12670874 - Tube - $32.10 23424013 - Hose - $20.65 23424015 - Fitting - $32.99 11547667 - Hose Clamp - $2.40 (x3) 11570871 - Hose Clamp - $3.23 (x2) 11519385 - Bolt - $2.87 (x2) Other stuff you'll probably need -------------------------------- - Tesa 50126 Wiring Harness Tape (2 rolls should do fine) https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 - Heat Exchanger - ZL1 Jack Pads from https://www.zl1addons.com. I would buy 4 with the jack pads if you plan to use a lift. They're worth the money. - PF64 Oil Filter and 11 quarts of oil (The first fill takes a little more than 10 quarts). - A fused relay, wiring, and loom for the coolant pump. I used the Painless Wiring 30821 Hlite Relay Kit #37827 and modified it to work like a normal relay. - Dexcool Coolant (2 gallons of concentrate and 2 gallons of distilled water will be plenty.) - Fir Tree Push Mount cable ties. I used these: https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 - A set of Push type retainer clips. The Swordfish 60010 kit has ones that match GM perfectly. https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 - Loctite 242 and 272... A tiny bottle of each will work fine. - A/C Vacuum Pump kit to recharge A/C System. I bought these and they worked great: FJC (6909) 3.0 CFM Vacuum Pump - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 Mountain 8205 R-134a Brass Manifold Gauge Set with Couplers - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 Mountain 8401 Top Style Metal Can Tap - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 ACDelco 10-9097 R134A (I think you need 2 cans. I would get 3 just to be sure.) - https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 - 19299818 - Brake and Clutch Fluid (FYI, to bleed the clutch on these you'll probably need to put a vacuum pump on the brake fluid reservoir. The bleeder is pretty much impossible to get to after the transmission is put back into the car.) - Lots of time Other Misc Stuff That You Probably Won't need -------------------------------------- 52474373 - A/C Compressor Seal - $4.20 12657093 - GM LT1, L83, L86 Exhaust Manifold Gasket - $4.03 11546600 - Exhaust manifold to engine bolt - $2.69 ea (x10) 11611992 - Supercharger lid bolt - $2.45 84044721 - Underhood fuse block (LT1) - $143.86 84063674 & 84063675 - Rear '17 SS 1LE Calipers - $240.00 each 12672471 - PCV Oil Separator - $80.04 12657430 - Water Manifold Gaskets - $2.48 ea (x2.) 12656725 - Engine Oil Cooler Line (Runs from the bottom of the water manifold to the rear of the engine oil cooler) - $50.42 23355791 – '17 SS 1LE Front Wheels 20 x 10 - $572.40 plus $50.00 core charge 23355802 - '17 SS 1LE Rear Wheels 20 x 11 - - $572.40 plus $50.00 core charge 23115614 - '17 SS 1LE Wheel Center Cap - $20.99 (x4) 13598786 (RPO code XL7 315mHz) or 13598787 (RPO code XL8 433mHz) - TPMS Sensor - $45.64 (x4) 24274085 - Clutch Slave Cylinder - $310.07 12644807 - LT4 MAP Sensor (just in case your engine comes with the wrong one like mine did) 12640390 - Knock Sensor Shield - $19.18 (The LT4 docs say you need to buy this, but mine came with it.) Last edited by travislambert; 12-17-2016 at 07:06 AM.