|
Hello, I am looking to do the same upgrade on my Camaro, do you know if the parts list is different on the convertible? I assume most of the parts will be the same but the camera mounting might be different, I cannot seem to locate any real documentation on the parts list for the PDR outside of the above.
Here are a few items I was able to find:
Vehicle Performance Data Recorder Malfunction:
Display Malfunction
1. Ignition OFF, disconnect the X1 harness connector at the K161 Performance Data Recorder.
2. Test for less than 10 Ω between the ground circuit terminal 12 and ground.
⇒ If 10 Ω or greater
2.1. Ignition OFF.
2.2. Test for less than 2 Ω in the ground circuit end to end.
⇒ If 2 Ω or greater, repair the open/high resistance in the circuit.
⇒ If less than 2 Ω, repair the open/high resistance in the ground connection.
⇓ If less than 10 Ω
3. Verify that a test lamp illuminates between the B+ circuit terminal 1 and ground.
⇒ If the test lamp does not illuminate
3.1. Ignition OFF, remove the test lamp.
3.2. Test for less than 2 Ω in the B+ circuit end to end.
⇒ If 2 Ω or greater, repair the open/high resistance in the circuit.
⇓ If the test lamp illuminates
4. Ignition OFF, connect X1 harness connector at the K161 Performance Data Recorder.
5. Disconnect the X2 harness connector at the K161 Performance Data Recorder.
6. Ignition ON.
7. Test for less than 1 V between the signal circuit terminal 6 and ground.
⇒ If 1 V or greater
7.1. Ignition OFF, disconnect the X1 harness connector at the A11 Radio. Ignition ON.
7.2. Test for less than 1 V between the signal circuit and ground.
⇒ If 1 V or greater, repair the short to voltage in the circuit.
⇒ If less than 1 V, replace the A11 Radio.
⇓ If less than 1 V
8. Test for less than 2 Ω in the signal circuit end to end.
⇒ If 2 Ω or greater
Repair the open/high resistance in the circuit.
⇓ If less than 2 Ω
9. Test for less than 1 V between the signal circuit terminal 12 and ground.
⇒ If 1 V or greater
9.1. Ignition OFF, disconnect the X1 harness connector at the A11 Radio. Ignition ON.
9.2. Test for less than 1 V between the signal circuit and ground.
⇒ If 1 V or greater, repair the short to voltage in the circuit.
⇒ If less than 1 V, replace the A11 Radio.
⇓ If less than 1 V
10. Test for less than 2 Ω in the signal circuit end to end.
⇒ If 2 Ω or greater
Repair the open/high resistance in the circuit.
⇓ If less than 2 Ω
11. Connect X2 harness connector at the K161 Performance Data Recorder.
12. Verify the three USB cables are properly connected at all components and there is no damage to the cable or connections.
⇒ If connection problems or cable damage is noted.
Perform the appropriate repair or replacement to correct any issues.
⇓ If no connection problems or cable damage is noted.
13. Ignition OFF, connect the EL-50334-50 to the P17 Info Display Module connector X5 and the performance data recorder connector X3.
14. Ignition ON, performance data recorder system ON.
15. Verify the performance data recorder system operates properly.
⇒ If performance data recorder system does not operate properly
15.1. Replace the P17 Info Display Module.
15.2. Verify the performance data recorder system operates properly.
⇒ If performance data recorder system does not operate properly
Replace the K161 Performance Data Recorder.
⇓ If performance data recorder system operates properly
All OK
⇓ If performance data recorder system operates properly
16. Replace the USB harness.
Record Malfunction
1. Ignition OFF, disconnect the X2 harness connector at the X20 Memory Card Receptacle.
2. Test for less than 10 Ω between the ground circuit terminal 4 and ground.
⇒ If 10 Ω or greater
2.1. Ignition OFF.
2.2. Test for less than 2 Ω in the ground circuit end to end.
⇒ If 2 Ω or greater, repair the open/high resistance in the circuit.
⇒ If less than 2 Ω, repair the open/high resistance in the ground connection.
⇓ If less than 10 Ω
3. Verify that a test lamp illuminates between the B+ circuit terminal 6 and ground.
⇒ If the test lamp does not illuminate
3.1. Ignition OFF, remove the test lamp.
3.2. Test for less than 2 Ω in the B+ circuit end to end.
⇒ If 2 Ω or greater, repair the open/high resistance in the circuit.
⇓ If the test lamp illuminates
4. Connect the X2 harness connector at the X20 Memory Card Receptacle.
5. Verify the USB cable is properly connected at all components and in-line connections, and there is no damage to the cable or connections.
⇒ If connection problems or cable damage is noted.
Perform the appropriate repair or replacement to correct any issues.
⇓ If no connection problems or cable damage is noted.
6. Connect the EL-50334-50 to the memory card receptacle connector X1 and the performance data recorder connector X5.
7. Ignition ON, performance data recorder system ON.
8. Verify the memory card receptacle operates properly while operating the performance data recorder system.
⇒ If memory card receptacle does not operate properly
8.1. Replace the X20 Memory Card Receptacle.
8.2. Verify the memory card receptacle operates properly while operating the performance data recorder system.
⇒ If memory card receptacle does not operate properly
Replace the K161 Performance Data Recorder.
⇓ If memory card receptacle operates properly
All OK
⇓ If memory card receptacle operates properly
9. Replace the USB harness.
|