CAMARO6 - View Single Post

Bilicki66 · 02-02-2020, 06:59 AM

Hey All, so we did our 1st build and we are super close to tuning it but just can’t seem to get it absolutely perfect. We are using HP Tuners and what’s happening is we are getting some cracking/popping at acceleration 40% and above throttle at random times. One pull on the street will do it and the next it won’t. At long idle sitting at red light when I go to take off sometimes care will pop,crackle and then I will lose rev match. I wanted to know if anyone has this close of a similar build and would be willing to share tune or input?

Here are the following mods.....

Speed engineering long tube headers 1 7/8” and catless pipes
Corsa sport exhaust
Phastek flex fuel system
Abel Racing catch can
Precision Race Components CNC Ported 2014+ LT1 Cylinder Heads, GM Castings
Texas Speed & Performance Gen 5 LT1 special grind Camshaft for road course
Texas Speed & Performance 7.85" Pushrod, 3/8" Diameter with 5/16" Ball Ends, Per Pushrod
4 Degree Phaser Limiter
Texas Speed & Performance Gen 5 LT1, DOD Delete Kit
DOD Hole Plug
ARP SBC 6.2L LT1 Head Bolt Kit Without Corner Bolts
GM LS2 Lifter Tray
Comp Cams OE-Replacement Hydraulic Roller Lifters, SBC & LS1
GM MLS Head Gasket
LT1 VVT CAMSHAFT BOLT / VALVE
GM Wet Sump Balancer Pulley Bolt
Water Pump Gasket
GM Front CRANK Seal
MSD Atomic AirForce LT1 Intake Manifold, 103mm, Red Lettering
HolleyDays Match
Nick Williams 103mm LTx Throttle Body Machined Finish

McLeod 6406807M RXT Twin Disc Clutch Kit With Steel Flywheel

BC Forged TD01
Thank you
👍👊🇺🇸🤘🏎🏁

02-02-2020, 06:59 AM	#1
Bilicki66 Drives: 2018 Camaro 2SS 1LE Join Date: Jun 2019 Location: edmond Oklahoma Posts: 15	Tuning help Hey All, so we did our 1st build and we are super close to tuning it but just can’t seem to get it absolutely perfect. We are using HP Tuners and what’s happening is we are getting some cracking/popping at acceleration 40% and above throttle at random times. One pull on the street will do it and the next it won’t. At long idle sitting at red light when I go to take off sometimes care will pop,crackle and then I will lose rev match. I wanted to know if anyone has this close of a similar build and would be willing to share tune or input? Here are the following mods..... Speed engineering long tube headers 1 7/8” and catless pipes Corsa sport exhaust Phastek flex fuel system Abel Racing catch can Precision Race Components CNC Ported 2014+ LT1 Cylinder Heads, GM Castings Texas Speed & Performance Gen 5 LT1 special grind Camshaft for road course Texas Speed & Performance 7.85" Pushrod, 3/8" Diameter with 5/16" Ball Ends, Per Pushrod 4 Degree Phaser Limiter Texas Speed & Performance Gen 5 LT1, DOD Delete Kit DOD Hole Plug ARP SBC 6.2L LT1 Head Bolt Kit Without Corner Bolts GM LS2 Lifter Tray Comp Cams OE-Replacement Hydraulic Roller Lifters, SBC & LS1 GM MLS Head Gasket LT1 VVT CAMSHAFT BOLT / VALVE GM Wet Sump Balancer Pulley Bolt Water Pump Gasket GM Front CRANK Seal MSD Atomic AirForce LT1 Intake Manifold, 103mm, Red Lettering HolleyDays Match Nick Williams 103mm LTx Throttle Body Machined Finish McLeod 6406807M RXT Twin Disc Clutch Kit With Steel Flywheel BC Forged TD01 Thank you 👍👊🇺🇸🤘🏎🏁