Homepage Garage Wiki Register Members List Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Search Forums


Phastek Performance


Showing results 1 to 30 of 500
Search took 0.07 seconds.
Search: Posts Made By: LiqTenExp
Forum: ZL1 Discussions Yesterday, 08:20 PM
Replies: 5
Views: 204
Posted By LiqTenExp
Engine\Airflow\General\MAP (this is just info...

Engine\Airflow\General\MAP (this is just info more or less about the expected values on car)
Max = 180 kPa
Min = 10 kPa

Engine\Airflow\General\MAP Estimation (these are the important values for...
Forum: ZL1 Discussions Yesterday, 08:04 PM
Replies: 5
Views: 204
Posted By LiqTenExp
Yeah, not sure why they went 4 bar... I actually...

Yeah, not sure why they went 4 bar... I actually considered going to 3 bar map to get better resolution in SD tuning but never got around to it.
Forum: ZL1 Discussions Yesterday, 06:46 PM
Replies: 5
Views: 204
Posted By LiqTenExp
Stock is a 4 bar TMAP, no need to change from the...

Stock is a 4 bar TMAP, no need to change from the perspective of pressure measurement limits.
Forum: ZL1 Discussions 09-17-2021, 10:16 AM
Replies: 17
Views: 824
Posted By LiqTenExp
Try placing the plastic funnel that comes with...

Try placing the plastic funnel that comes with the car (in trunk) into gas fill tube to open the anti-siphon valve and then insert a small diameter hose through it?
Forum: ZL1 Discussions 09-14-2021, 02:10 PM
Replies: 24
Views: 784
Posted By LiqTenExp
Good choice with the Swaintech, same here! I have...

Good choice with the Swaintech, same here! I have no issues with header to plug wire heating/damage.
Forum: ZL1 Discussions 09-14-2021, 11:59 AM
Replies: 24
Views: 784
Posted By LiqTenExp
Check plug wires, plugs, coil pack wires (make...

Check plug wires, plugs, coil pack wires (make sure the female contacts are locked and not becoming recessed when inserted into coil pack).

If your headers do not have a high quality coating to...
Forum: Forced Induction Discussions 09-12-2021, 07:15 PM
Replies: 22
Views: 607
Posted By LiqTenExp
https://www.amazon.com/Injector-Replace-EN-49245-E...

https://www.amazon.com/Injector-Replace-EN-49245-EN-51105-18683AA000/
Forum: Forced Induction Discussions 09-11-2021, 04:30 PM
Replies: 22
Views: 607
Posted By LiqTenExp
I wouldn't say it is extending anything, just...

I wouldn't say it is extending anything, just preventing leaks via damage during install with new seals.

I know my replacement injector set went in like butter when replaced after using that tool...
Forum: Forced Induction Discussions 09-11-2021, 04:11 PM
Replies: 22
Views: 607
Posted By LiqTenExp
You are missing of the purpose of the tool...

You are missing of the purpose of the tool completely.

That tool (245-4) does not install anything, it shapes/compresses the teflon seals AFTER installation or on brand new injectors prior to...
Forum: Forced Induction Discussions 09-11-2021, 02:19 PM
Replies: 22
Views: 607
Posted By LiqTenExp
It compresses/shapes the teflon seals so they...

It compresses/shapes the teflon seals so they don't hang up on install. Service manual calls to use one...
Forum: Forced Induction Discussions 09-11-2021, 09:13 AM
Replies: 22
Views: 607
Posted By LiqTenExp
Make sure to get an injector seal tool to...

Make sure to get an injector seal tool to pre-size them before insertion! Something like this: https://www.amazon.com/gp/product/B088TLZBRT The part labeled 245-4 in the picture is really all you...
Forum: ZL1 Discussions 09-08-2021, 07:47 PM
Replies: 20
Views: 1,184
Posted By LiqTenExp
Statement below is incorrect. If you disconnect...

Statement below is incorrect. If you disconnect MAF sensor IAT1/IAT2 will disappear and MAT will not move. MAT comes from the TMAP sensor temperature output. This is located post blower intercoolers...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 09-04-2021, 10:41 AM
Replies: 8
Views: 591
Posted By LiqTenExp
For some reason I remember something like this...

For some reason I remember something like this happening when my MAF was disconnected. Check that? If you have the ability to inspect sensor readings check temp and pressure sensors for valid...
Forum: ZL1 Discussions 08-24-2021, 07:05 PM
Replies: 16
Views: 825
Posted By LiqTenExp
What are you doing for the rear?

What are you doing for the rear?
Forum: ZL1 Discussions 08-19-2021, 07:01 AM
Replies: 18
Views: 1,585
Posted By LiqTenExp
Whatever happened here?

Whatever happened here?
Forum: ZL1 Discussions 08-19-2021, 06:58 AM
Replies: 2
Views: 282
Posted By LiqTenExp
Here are mine for a M6 ZL1, I had posted them in...

Here are mine for a M6 ZL1, I had posted them in another thread and then I saw another thread referenced them
Forum: ZL1 Discussions 08-15-2021, 07:27 PM
Replies: 15
Views: 1,305
Posted By LiqTenExp
Excess oil on clean side separator system, like a...

Excess oil on clean side separator system, like a bad lifter? The line that goes to brake booster is right at the TB, the clean side separator pulls from intake and the first place the oil would go...
Forum: ZL1 Discussions 08-14-2021, 07:25 PM
Replies: 20
Views: 2,132
Posted By LiqTenExp
Another vote for LS3 seals front/rear and Metco...

Another vote for LS3 seals front/rear and Metco breather. I'm running this on my current setup.
Forum: ZL1 Discussions 08-12-2021, 05:46 AM
Replies: 4
Views: 221
Posted By LiqTenExp
That'll be 5 dollars please :) JK That is...

That'll be 5 dollars please :) JK

That is kinda how my current setup looks, there is some stuff not needed but I've looked at and just not deleted. It definitely is enough to do VVE, MAF,...
Forum: ZL1 Discussions 08-10-2021, 04:44 PM
Replies: 18
Views: 1,585
Posted By LiqTenExp
I can't wait for someone to figure this out, this...

I can't wait for someone to figure this out, this is some weird data your car is producing.

The MAP is isn't following the MAF above 40kPa (6 psi / -8.7 psia) in run 2 but somehow in run 1 it...
Forum: ZL1 Discussions 08-09-2021, 08:27 PM
Replies: 18
Views: 1,585
Posted By LiqTenExp
That MAT temp of 149°F is about right for a well...

That MAT temp of 149°F is about right for a well maintained stock LT4 IC system with 195°F ECT in 95°F ambient. It picked up ~7° after the pull so something was making heat due what you'd hope was...
Forum: ZL1 Discussions 08-09-2021, 09:55 AM
Replies: 21
Views: 1,445
Posted By LiqTenExp
MAT is not based on IAT2 (there is no IAT2 sensor...

MAT is not based on IAT2 (there is no IAT2 sensor on LT4), it is based on TMAP sensor.
Forum: Forced Induction Discussions 08-08-2021, 07:49 AM
Replies: 59
Views: 3,400
Posted By LiqTenExp
I don't know why HP Tuners has IAT1 under ECM and...

I don't know why HP Tuners has IAT1 under ECM and CCM. It could be that the physical sensor wiring goes to CCM and then just passes the data up to ECM (hence the dual PID). I don't have a service...
Forum: Forced Induction Discussions 08-07-2021, 07:08 PM
Replies: 9
Views: 503
Posted By LiqTenExp
You should be able to add least add those...

You should be able to add least add those additional parameters going forward and capture what is going on here forward.

You can take a look on YouTube for GenV VT tuning to get a visual version...
Forum: Forced Induction Discussions 08-07-2021, 06:14 PM
Replies: 9
Views: 503
Posted By LiqTenExp
See the Torque Mgt Advance Parameter?, its...

See the Torque Mgt Advance Parameter?, its pulling 20° of timing. Your TB is also closed further than it should be relative to pedal position.

Add the following to Chart Vs Time:

Accelerator...
Forum: Forced Induction Discussions 08-07-2021, 08:55 AM
Replies: 59
Views: 3,400
Posted By LiqTenExp
I went back and checked, 2128 is what HP Tuner...

I went back and checked, 2128 is what HP Tuner calls IAT2 and is what my data I've been presenting is using. My prior post had the incorrect value typed, I fixed it for posterity. There is only 1...
Forum: Forced Induction Discussions 08-06-2021, 01:52 PM
Replies: 59
Views: 3,400
Posted By LiqTenExp
Here is a log of when my IC circuit ran out of...

Here is a log of when my IC circuit ran out of coolant due to a leak in drivers side brick. I had no coolant left and if IAT2 really represents TMAP (aka post IC bricks) it should have gone sky high,...
Forum: Forced Induction Discussions 08-06-2021, 01:39 PM
Replies: 59
Views: 3,400
Posted By LiqTenExp
Ted, I am willing to learn something here,...

Ted,

I am willing to learn something here, and would like to figure out why all my evidence below is incorrect.

I just went down to my car and pulled the MAF connector. Both IAT1 and IAT2...
Forum: Forced Induction Discussions 08-05-2021, 05:04 PM
Replies: 59
Views: 3,400
Posted By LiqTenExp
MAT, third from bottom

MAT, third from bottom
Forum: Forced Induction Discussions 08-05-2021, 02:35 PM
Replies: 59
Views: 3,400
Posted By LiqTenExp
For stock ZL1 the physical sensors are (I have...

For stock ZL1 the physical sensors are (I have manually pulled IAT1 and TMAP sensors and confirmed the mapping):

IAT1 = MAF temp sensor
IAT2 = N/A (value is IAT1+math)
MAT = TMAP (Temperature...
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 12:20 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2021, vBulletin Solutions, Inc.