Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Search Forums


Bigwormgraphix


Showing results 1 to 30 of 500
Search took 0.05 seconds.
Search: Posts Made By: LiqTenExp
Forum: ZL1 Discussions 12-05-2023, 06:16 PM
Replies: 59
Views: 9,266
Posted By LiqTenExp
I'm running the 2 gallon fender tank with...

I'm running the 2 gallon fender tank with magnuson capped tank. Just consider suction/pressure side of the pump and how it will fill the system.
...
Forum: ZL1 Discussions 12-02-2023, 10:01 AM
Replies: 1
Views: 775
Posted By LiqTenExp
M6x0.8mm

M6x0.8mm
Forum: ZL1 Discussions 11-20-2023, 06:36 PM
Replies: 1
Views: 775
Posted By LiqTenExp
Missing bolt, lol

Looking for the bolt that holds the ZL1 manual transmission cooling lines up the right hand side of the engine. There are two line coupled together at this point and my bolt has gone missing... I...
Forum: ZL1 Discussions 11-12-2023, 04:47 PM
Replies: 8
Views: 588
Posted By LiqTenExp
I've got 345/30R19 Nitto 555RII on there now with...

I've got 345/30R19 Nitto 555RII on there now with 305/30R19 PS4S on the front. PS4S don't come in 345 but 355/30R19, OMG are they expensive! ($719 each)
Forum: ZL1 Discussions 11-11-2023, 04:12 PM
Replies: 8
Views: 588
Posted By LiqTenExp
Yes, we obviously didn't test it on anything with...

Yes, we obviously didn't test it on anything with a crown.
Forum: ZL1 Discussions 11-11-2023, 10:46 AM
Replies: 8
Views: 588
Posted By LiqTenExp
Yeah, that was my plan next. I actually need new...

Yeah, that was my plan next. I actually need new rears so it might be the plan for next year.
Forum: ZL1 Discussions 11-11-2023, 08:53 AM
Replies: 8
Views: 588
Posted By LiqTenExp
Pulling to the right

Have an issues with the car pulling to the right. Spent hours working with a great shop in Clifton and we ran out of time. Front suspension is completely stock. Rear is all BMR non-adjustable except...
Forum: ZL1 Discussions 10-31-2023, 05:49 AM
Replies: 97
Views: 19,304
Posted By LiqTenExp
Glad it worked out. Mine is still humming away 3+...

Glad it worked out. Mine is still humming away 3+ years later.
Forum: ZL1 Discussions 08-27-2023, 11:38 AM
Replies: 5
Views: 547
Posted By LiqTenExp
Agree with above. Just epoxy it back into place....

Agree with above. Just epoxy it back into place. someone shoved something under there and hit the speaker.
Forum: ZL1 Discussions 08-25-2023, 07:23 AM
Replies: 6
Views: 609
Posted By LiqTenExp
No. You would be leaving some power on the...

No.

You would be leaving some power on the table with not assessing if you can place a few more degrees of timing in due to lower MAT
Forum: ZL1 Discussions 08-07-2023, 04:02 PM
Replies: 14
Views: 1,450
Posted By LiqTenExp
Another vote for Gates green belts

Another vote for Gates green belts
Forum: Wheels | Tires -- Sponsored by The Tire Rack 08-05-2023, 03:40 PM
Replies: 3
Views: 603
Posted By LiqTenExp
I'm running 555RII in 345/30R19 on the Apex 19x12...

I'm running 555RII in 345/30R19 on the Apex 19x12 ZL1 wheels in the rear. It's the best daily driver drag radial out there. You do need to get them up to temp and scrub them off (aka burn out) once a...
Forum: ZL1 Discussions 08-05-2023, 03:28 PM
Replies: 15
Views: 1,441
Posted By LiqTenExp
Sounds like you shouldn't worry about battery or...

Sounds like you shouldn't worry about battery or tune.

That first one had me going for a loop. I did swap coils and it worked, for a little, it just wound up being a slightly better connection...
Forum: ZL1 Discussions 08-05-2023, 11:09 AM
Replies: 15
Views: 1,441
Posted By LiqTenExp
Some issues to look out for when I've had similar...

Some issues to look out for when I've had similar oddities with misfires that go beyond the obvious ones you've covered:

1) Coil pack pin within connector not locked in place and backed out (only...
Forum: ZL1 Discussions 07-31-2023, 05:58 AM
Replies: 28
Views: 2,759
Posted By LiqTenExp
Line lock is in all ZL1 2017+

Line lock is in all ZL1 2017+
Forum: ZL1 Discussions 07-28-2023, 07:21 AM
Replies: 20
Views: 1,273
Posted By LiqTenExp
Run 50/50 water/methanol as a cooling method to...

Run 50/50 water/methanol as a cooling method to MAT and you will clean your engine every time you get on it :)
Forum: ZL1 Discussions 06-09-2023, 06:23 PM
Replies: 24
Views: 1,969
Posted By LiqTenExp
93 + 50/50 Meth ~24°

93 + 50/50 Meth ~24°
Forum: ZL1 Discussions 06-02-2023, 08:22 AM
Replies: 24
Views: 2,361
Posted By LiqTenExp
Please don't take my next comments as anything...

Please don't take my next comments as anything negative towards Octane boosters...

I stopped using Boostane after a couple WB02 sensor failures and an Injector issue. I switched to water/meth and...
Forum: ZL1 Discussions 06-01-2023, 09:17 AM
Replies: 4
Views: 1,231
Posted By LiqTenExp
You should be somewhere in the single digit...

You should be somewhere in the single digit positive degrees of timing at idle. At negative timing you will be excessively heating up your exhaust manifolds/headers. Are you doing the tuning? I can...
Forum: ZL1 Discussions 05-17-2023, 11:56 AM
Replies: 11
Views: 1,294
Posted By LiqTenExp
Note, im not at 1000whp but I didn't swap mine...

Note, im not at 1000whp but I didn't swap mine due to failure/slipping, the trans was coming out and I did it as preventative maintenance. Stock clutch is a beast.
Forum: ZL1 Discussions 05-17-2023, 06:35 AM
Replies: 11
Views: 1,294
Posted By LiqTenExp
I'm running McLeod RTX (twin disc), drives like...

I'm running McLeod RTX (twin disc), drives like stock. No regrets, not saying it is the only/best option but an option.
Forum: ZL1 Discussions 05-09-2023, 09:26 PM
Replies: 22
Views: 2,627
Posted By LiqTenExp
I asked Rotofab what element material flowed...

I asked Rotofab what element material flowed better and they said oiled, as noted big gulp only comes oiled.
Forum: ZL1 Discussions 05-04-2023, 08:33 PM
Replies: 97
Views: 19,304
Posted By LiqTenExp
look at page 8 on here:...

look at page 8 on here: https://www.jmschip.com/content/PowerMAX_V2/PM2000-PM2020_Install_Universal_v11_WEB.pdf
Forum: ZL1 Discussions 04-27-2023, 04:36 AM
Replies: 5
Views: 1,036
Posted By LiqTenExp
This is another good option:...

This is another good option: https://dedicatedmotorsports.com/ZL1-2GAL/

My installation of it: https://www.camaro6.com/forums/showthread.php?t=610199

It stays much cooler as it is not in the...
Forum: ZL1 Discussions 04-09-2023, 05:05 PM
Replies: 4
Views: 1,169
Posted By LiqTenExp
How's that 3.0 whipple? I'm concerned with the...

How's that 3.0 whipple? I'm concerned with the quality of whipple vs. magnuson and haven't done enough research on 3.0 whipple vs 2650 results.
Forum: ZL1 Discussions 04-09-2023, 04:03 PM
Replies: 0
Views: 478
Posted By LiqTenExp
Delete

Delete
Forum: ZL1 Discussions 04-09-2023, 03:26 PM
Replies: 4
Views: 1,169
Posted By LiqTenExp
2017 ZL1 Compression Test

Hey,

I try to do a compression test at the beginning of the season and appear to have pretty good results for a 6 year old car that has been modified for 5 years (250+ whp).

The min to max was...
Forum: ZL1 Discussions 04-04-2023, 06:19 AM
Replies: 6
Views: 1,109
Posted By LiqTenExp
https://www.camaro6.com/forums/showthread.php?t=58...

https://www.camaro6.com/forums/showthread.php?t=586572
Forum: ZL1 Discussions 04-03-2023, 07:02 AM
Replies: 47
Views: 5,427
Posted By LiqTenExp
What size TB is it compatible with? Right now I...

What size TB is it compatible with? Right now I have a 103mm adapter on my 2300 for my Katech 103mm TB.
Forum: ZL1 Discussions 04-02-2023, 05:22 PM
Replies: 47
Views: 5,427
Posted By LiqTenExp
How's the 3.0 working out for you? I've been...

How's the 3.0 working out for you? I've been considering upgrading from my 2300
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 05:08 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.