CAMARO6
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

CAMARO6 (https://www.camaro6.com/forums/index.php)
-   Tuning / Diagnostics (https://www.camaro6.com/forums/forumdisplay.php?f=254)
-   -   Wideband not showing up in HP Tuners (https://www.camaro6.com/forums/showthread.php?t=581904)

yourmomshouse 09-17-2020 10:42 PM
Wideband not showing up in HP Tuners
 
Anyone have any advice on how to get the wideband data to show up on hpt software. The gauge itself works, I added the wideband to the parameter list, but once I connect the car and start it up, that the wideband part on the list goes blank. I also see that there are multiple channels. Could it be because I added the wrong channel? Getting remote tuned, pretty much I've gotta figure this out to log correctly.

Joshinator99 09-18-2020 05:41 AM
Quote:
Originally Posted by yourmomshouse (Post 10870031)
Anyone have any advice on how to get the wideband data to show up on hpt software. The gauge itself works, I added the wideband to the parameter list, but once I connect the car and start it up, that the wideband part on the list goes blank. I also see that there are multiple channels. Could it be because I added the wrong channel? Getting remote tuned by Pray, pretty much I've gotta figure this out to log correctly.
Which wideband? Which parameter? Hopefully you went for the AEM 30-0334 since that’s the easiest one to integrate into HP Tuners.

yourmomshouse 09-18-2020 06:34 AM
Quote:
Originally Posted by Joshinator99 (Post 10870078)
Which wideband? Which parameter? Hopefully you went for the AEM 30-0334 since that’s the easiest one to integrate into HP Tuners.
That's the wideband I have. I need to add the AFR to the list so that my tuner, Brett can see it to fine tune... I followed the video by HPT on Youttueb showing how to do this. I can see it on the list, but once I press record it disappears and that line goes blank...:noidea:

scantone 09-18-2020 07:07 AM
Type in WB EQ it will be under oxygen sensors not X Series UEGO. At least this was the case with mine the other day, I was having the same problem.

LiqTenExp 09-18-2020 07:26 AM
Agree, look for WB EQ 1 (SAE) and add that as a channel. Make sure to connect to the car after it has been put in run (not started or started) then start recording or it may not show up.

KingLT1 09-18-2020 08:45 AM
Try to repoll all parameters after you connect the scanner(with the car on and not running... in accessory mode) so it will see the wideband.

Joshinator99 09-18-2020 12:34 PM
Quote:
Originally Posted by scantone (Post 10870106)
Type in WB EQ it will be under oxygen sensors not X Series UEGO. At least this was the case with mine the other day, I was having the same problem.
Quote:
Originally Posted by LiqTenExp (Post 10870117)
Agree, look for WB EQ 1 (SAE) and add that as a channel. Make sure to connect to the car after it has been put in run (not started or started) then start recording or it may not show up.
Quote:
Originally Posted by KingLT1 (Post 10870155)
Try to repoll all parameters after you connect the scanner(with the car on and not running... in accessory mode) so it will see the wideband.
:word:

yourmomshouse 09-19-2020 01:05 AM
thanks for everyones help! Im gonna try this later

Purplt1 09-19-2020 08:06 PM
If what everyone said above doesnt work..Go to the settings on the AEM wide band. If you see CAN you need to send the gauge to AEM. If you see OBD you are ok. AEM put the wrong firmware in some gauges . I just just went through this issue and come to find out I had the gauge with the wrong firmware.

New_image 09-20-2020 04:18 PM
I had the same problem. I was using the Bluetooth to log. As soon i hardwired to laptop...problem solved.

yourmomshouse 10-22-2020 08:22 PM
Quote:
Originally Posted by Purplt1 (Post 10870873)
If what everyone said above doesnt work..Go to the settings on the AEM wide band. If you see CAN you need to send the gauge to AEM. If you see OBD you are ok. AEM put the wrong firmware in some gauges . I just just went through this issue and come to find out I had the gauge with the wrong firmware.
This was the issue. THey sent me CAN. They told me to send in a video or pictures of me destroying the gauge and I did. They sent out a brand new OBD one. Installed it, problem solved. What a headache!

Purplt1 10-25-2020 04:38 PM
Quote:
Originally Posted by yourmomshouse (Post 10890086)
This was the issue. THey sent me CAN. They told me to send in a video or pictures of me destroying the gauge and I did. They sent out a brand new OBD one. Installed it, problem solved. What a headache!
I had to destroy mine too. I was trying to get it to work for 3 days smh. Glad you got it fixed.

Timbo-1LE 04-13-2021 05:49 PM
I have the same problem. Says odb, but channel disappears when you start to log. Any other ideas?

LiqTenExp 04-14-2021 05:15 AM
Just do this and you will be fine:

Find WB EQ 1 (SAE), add that as a channel. Make sure to connect to the car after it has been put in run (can be engine on/off) then start recording or it may not show up


All times are GMT -5. The time now is 03:16 PM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.