03-26-2014, 06:32 PM | #29 | |
|
Quote:
Looks mean!! Glad you like it! |
|
11-01-2015, 06:39 AM | #30 |
sorry to revive a dead but what did you guys use to fill the 7th hole that is created by the clip on the factory spoiler?
|
|
11-01-2015, 03:40 PM | #31 |
|
Nothing. It doesn't show . Also I used 1/8" thick foam tape the full length of the trunk lid to seal the spoiler to the trunk .
__________________
Mods, K&N CAI ,VTC , GM Perf Axleback Exhaust, Elite Eng CC and CSS, GM Strut Tower Brace,Carbon Fiber Anvil Spoiler,ASC T5 Splitter,Gen5diy Foglight kit.
|
11-01-2015, 04:14 PM | #32 |
having FUN now 13.66@101
|
Nothing as I have a 2010 and all my holes were used as the Anvil has studs in the stock locations.
__________________
|
11-01-2015, 04:41 PM | #33 | |
Quote:
Sent from my SM-G900T using Tapatalk
__________________
12.3 @113MPH - Full Bolt-Ons w/ Nitto 555r on 18" wheel
|
||
11-01-2015, 09:51 PM | #34 |
|
Nope no water leaking in .
__________________
Mods, K&N CAI ,VTC , GM Perf Axleback Exhaust, Elite Eng CC and CSS, GM Strut Tower Brace,Carbon Fiber Anvil Spoiler,ASC T5 Splitter,Gen5diy Foglight kit.
|
11-03-2015, 07:12 AM | #35 |
A legend in his own mind
Drives: 2010 2SS/RS M6 Join Date: May 2013
Location: Long Island, New York
Posts: 827
|
The anvil spoiler covers all of the stock spoiler holes in the decklid correct? Im pretty much sold on this spoiler. I absolutely love it.
|
11-03-2015, 08:02 AM | #36 |
It does. I installed mine this past weekend and I absolutely love it. Best looking spoiler IMO. I had to drill out a few of the holes to get it to fit, and I know a few others have had to do the same. Just to be safe I put some molding tape over the 7th hole that is not utilized by the Anvil.
|
|
11-03-2015, 08:37 AM | #37 | ||
having FUN now 13.66@101
|
Quote:
Yes, all 6 stock holes will be used. Might have to open them up a bit to get better fitment. I know I did. (see my above post # 27) Hopefully you can find an Anvil spoiler to buy, they are hard to come by. Quote:
Since you have a 2015 you have the extra hole. the above person has a 2010 (as I did) and there are only the 6 holes. I agree, the holes need to be opened and the Anvil pulled rearward for better placement and fitment. For sure the best looking spoiler out there IMHO too. It was the one my wife liked the most as she said the rest were UGH. So I knew I had the right one for me to replace my stock one. Other thing to do is squeeze some silicone around the stud and nut from the inside to help seal the hole up too. I also place a piece of thick molding foam around the hole from the outside too. And around the perimeter where it touches down on the deck lid and makes contact with the edge of the quarter panel.
__________________
|
||
11-03-2015, 08:37 AM | #38 |
[COTW 5/12/14]
Drives: 2012 CRT NF Cammed 2SS/RS For Sale Join Date: Oct 2011
Location: NOLA
Posts: 6,115
|
I had a body shop install mine and they said they didn't have to drill out any of the holes, it was all good
|
11-07-2015, 08:52 AM | #39 |
Drives: 2013 AGM 1SS/RS LS3 Join Date: Mar 2011
Location: Cedar Falls, Iowa
Posts: 1,581
|
I raised mine with some rubber washers and used the rubber pads supplied with the spoiler to protect the paint.
I also had to lightly open up a couple of the factory holes to get it to drop in. The 2 in the middle and then on my 2013 the far left hole is actually a slot. It didn't take long with a file. I love my Anvil spoiler.
__________________
2013 Camaro 1SS/RS - Ashen Gray Metallic
| LS3 | CAI Inductions, Inc Intake | Vmax Ported Throttle Body | Dynatech 1.875" Long Tube Headers | Apex Scoop & Washer Bottle Relocation | Lethal Racing Night Fury Cam | BTR 7.400" Push Rods |LS2 Dampener | Melling 10296 Oil Pump | IWIS Chain | BTR .660" Dual Valve Springs | BTR Trunion Upgrade Kit | Lethal Racing Tuned | Anvil Notch Spoiler | BMR Split Drop Springs | Eaton TrueTrac | GM 3.91 Gears | LPW Diff Cover | Rohana RF2 275/40 20x10F 315/35 20x11R | BMR Polyurethane Motor Mounts |
11-11-2015, 02:14 PM | #40 | |
Quote:
http://www.walmart.com/ip/3M-Super-S...2-x-5/16913678 Sent from my SM-G900T using Tapatalk
__________________
12.3 @113MPH - Full Bolt-Ons w/ Nitto 555r on 18" wheel
|
||
11-11-2015, 07:25 PM | #41 | |
having FUN now 13.66@101
|
Quote:
The 1/2" thick stuff do you mean wide? I would not use two sided tape. No reason too. The spoiler is held in place with the studs and nuts. The tape is merely to protect the paint where it touches down on the deck lid and qtr. panel.
__________________
|
|
11-11-2015, 08:39 PM | #42 | |
Quote:
Sent from my SM-G900T using Tapatalk
__________________
12.3 @113MPH - Full Bolt-Ons w/ Nitto 555r on 18" wheel
|
||
|
|
|
|