You are browsing camaro6 
10-19-2017, 11:54 AM
|
#323 |
 Drives: 2017 zl1 Join Date: Oct 2017
Location: Canyon Country
Posts: 23
|
Just tried ordering the PX1 for my 2018 ZL1 and they are not in stock!!!!!!! WHAT!?!?!?!?! Does anyone know where else I can get lowering springs that can lower the car 1.5" or when they will have them in stock.
|
|
|
|
10-21-2017, 07:49 PM
|
#324 |
 Drives: 2017 Camaro 2SS Join Date: Dec 2016
Location: Houston
Posts: 469
|
I'm sure Ricardo will chime in. I can't wait to install mine. Waiting on my powerstop pads to come in this week.
|
|
|
|
|
10-22-2017, 09:29 PM
|
#325 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,860
|
PM Ricardo and he can get you set up. I've had mine on for 1 1/2 or so. Love them and ride is great and they still transfer weight at the drag strip for upper 1.40 sixty foot times.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
 |
|
|
|
|
10-23-2017, 09:01 AM
|
#326 | |
 
Drives: the boss nuts.... Join Date: Aug 2012
Location: Houston, TX
Posts: 1,428
  |
Quote:
From what I know and have seen we are the only ones with a drop spring that is that low. Thank you, Ricardo |
|
|
|
|
|
10-23-2017, 11:45 AM
|
#327 |
|
Drives: 2017 Camaro 2SS Join Date: Dec 2016
Location: Houston
Posts: 469
|
Ok, so I hae now read through this entire post...again. It appears most of those running these springs are using a 285/30 front and 305/30 rear.
Is anyone running a 285/35 and 305/35 combo with these springs on a non MRC car? If so, are there any issues with rubbing...other than the obvious wiring harness? I would like to open a couple additional tire choices with the 285/35 and 305/35. However, if it is not possible it is not possible. Also, I will be running these on the MRR M017 wheels in a 20x10 front and 20x11 rear. |
|
|
|
|
10-23-2017, 07:58 PM
|
#328 |
|
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,860
|
I run a 295-35-20 on the rear and a 275-35-20 on the front. 9's up front and 10's in the rear. I like my stuff tucked under the car. Looks awesome
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
|
|
|
10-31-2017, 09:21 PM
|
#329 |
|
Drives: 2017 Camaro 2SS Join Date: Dec 2016
Location: Houston
Posts: 469
|
Can someone with Phastek PX1 springs and factory 20" wheels take ground to fender (centered) measurements front and rear, please?
I did not remember to take pre-install measurements as I already had the car on jack stands to remove the front fascia for grill replacement. My current ride heights are: DF: 27 7/8" DR: 28 1/8" PF: 27 7/8" PR: 28 1/8" Above measurements may vary by 1/16". I had the alignment shop loosen and retorque everything today, but want to make sure i am near the correct lowered measurements. Don't want premature bushing wear. Also, I have a non-MRC 2017 Camaro 2SS. Thanks for all your help and Ricardo thanks for putting up with all my questions along the way (facebook). |
|
|
|
|
11-29-2017, 02:51 PM
|
#330 |
|
Drives: 2017 Camaro ss garnet red tintcoat Join Date: Nov 2017
Location: Reno nv
Posts: 9
|
Anyone with mag ride have these springs? Any pics?
|
|
|
|
|
12-06-2017, 12:48 PM
|
#331 | |
|
Drives: the boss nuts.... Join Date: Aug 2012
Location: Houston, TX
Posts: 1,428
|
Quote:
1LE:  ZL1:  
|
|
|
|
|
|
12-09-2017, 01:04 PM
|
#332 | |
|
Drives: 2017 Camaro ss garnet red tintcoat Join Date: Nov 2017
Location: Reno nv
Posts: 9
|
Quote:
Ok thank u was trying to debate on the px1 springs and eibachs wanted to see which lowered more with mag ride. |
|
|
|
|
|
03-21-2018, 06:39 PM
|
#333 |
 
Drives: 2016 Camaro 1SS (Dory) Join Date: Jun 2017
Location: San Jose, Ca
Posts: 93
|
So did we ever get spring compression rates for these? I haven't been able to find anything
|
|
|
|
|
04-04-2018, 03:06 PM
|
#334 |
|
Sinister6.2
Drives: 2017 Mosaic Black 2SS A8 Join Date: Sep 2016
Location: Ontario, Canada
Posts: 9
|
Just ordered a set of the springs today. I will be putting them on my 2017 Camaro SS with Mag ride. Excited to see the difference.
__________________
2017 Mosaic Black Camaro 2SS A8
September 29th, 2016 - Order Placed November 14th, 2016 - Car built November 21st, 2016 - took delivery of my new Camaro! |
|
|
|
|
04-05-2018, 11:24 PM
|
#335 |
 Drives: 2019 Camaro ZL1 Join Date: Apr 2018
Location: Ontario
Posts: 198
|
Any updates for v6?
|
|
|
|
|
04-07-2018, 09:30 PM
|
#336 |
|
The Mechanic
Drives: 1SS M Join Date: Dec 2017
Location: NJ
Posts: 291
|
I want to know since these are the lowest springs possible what kind of data are we looking at to show these wont blow out the shocks or cause the to leak in a year or 2 like 90s and 2000s cars always did on lowered springs with stock shocks? I love the look but i dont want to destroy my shocks in exchange for it
|
|
|
|
|
|
|
|
|
Post Reply
|
| Tags |
| camaro springs, lower, lowering springs, phastek springs, springs |
|
|
