You are browsing camaro5 
 |
|
03-20-2016, 12:12 PM
|
#1 |
 
|
Anyone purchased the Phastek Performance blacked out tail light bezels?
i know i can plasti dip them but i want the gloss look. i did prep and paint them but i dont know how long they will last? so i seen that phastek has a set in either flat or gloss black that claim to be chip and fade resistant... for only $60 anyone buy these for there beast yet? and if so how are they holding up your reviews are greatly appreciated. thanks
http://www.phastekperformance.com/20...tail-bezel.htm 
__________________
That Mustang Was Fast! It Was Really Hauling Ass When I Passed It!
|
|
|
|
03-20-2016, 12:16 PM
|
#2 |
|
Account Suspended
Drives: black and silver Join Date: Apr 2014
Location: new york
Posts: 1,728
|
i bought them in gloss the are still good...
|
|
|
|
|
03-20-2016, 12:35 PM
|
#3 |
|
The Stealth Bumblebee
Drives: Black 2013 2LS Join Date: Aug 2013
Location: SW of Houston
Posts: 1,385
|
I bought them in gloss, but didn't put them on because they don't quite match the black paint on my car. Now if you don't have a black car then it should be ok, its just a slight difference imo.
Which ever way you go it will look a lot meaner than chrome.
__________________
KILLER BEE
 Last edited by CruisingSpeed; 03-20-2016 at 01:35 PM. |
|
|
|
|
03-20-2016, 03:02 PM
|
#4 |
 Drives: 2011 SS/RS convertible Join Date: Feb 2016
Location: Bryant, al
Posts: 60
|
Can of plasti dip $7
A little bit of time $free Results $priceless 
|
|
|
|
|
03-23-2016, 07:24 AM
|
#5 |
 
|
I went the plasti dip route and used their glossifier to give it the gloss effect. It's not as shiny and "black" as real paint would be but it does the job for way less 👍
Sent from my SM-G900T using Tapatalk
__________________
 |
|
|
|
|
03-23-2016, 10:39 AM
|
#6 |
       
|
I bought mine off of Amazon . Flat black . Look great .
__________________
 Mods, K&N CAI ,VTC , GM Perf Axleback Exhaust, Elite Eng CC and CSS, GM Strut Tower Brace,Carbon Fiber Anvil Spoiler,ASC T5 Splitter,Gen5diy Foglight kit. |
|
|
|
|
03-23-2016, 11:00 AM
|
#7 |
|
Put the Anzo flat black set on from jegs a while back and they are holding up great
__________________
 |
|
|
|
|
03-23-2016, 11:13 AM
|
#8 |
|
BUMBLLB
|
I bought these from ebay but I would have bought the ones from Phastek if i saw them first.
http://www.ebay.com/itm/321443869171
__________________
 |
|
|
|
|
03-23-2016, 11:17 AM
|
#9 |
Drives: 2012 Camaro SS/RS Join Date: Aug 2013
Location: Exton, PA
Posts: 320
|
Sorry to jack thread ... is it difficult to get these out / put in new ones?
|
|
|
|
|
03-23-2016, 11:20 AM
|
#10 | ||
|
BUMBLLB
|
Quote:
__________________
|
||
|
|
|
|
03-23-2016, 11:25 AM
|
#11 |
 
|
Lightly sanded, Used adhesion promoter and flat black for $14 total and still looks great a year later. Just takes a little time. Just took a few mins to be able to remove them all with a screwdriver. There's probably a better and safer way to do this but saw a couple people on YouTube use screwdrivers and worked great...no broken tabs or scratches.
__________________
Hotchkis Lowering Springs, Pfadt Balance Rear Sway Bar, BMR End Links, Cadillac ATS Front Brembo 4-Piston Brakes, VMAX Ported Throttle Body, VMAX Ice-olator, Volant Cold Air Intake, Magnaflow Resonated X-Pipe, Magnaflow Axle-Back Exhaust, JEGS Exhaust Cutouts, GM Strut Tower Brace, Hurst Comp Shifter, Heritage Front Grill, 3D Carbon Front Air Dam, T-Rex Lower Billet Grill, 3D Carbon Front Vendor Vents, 20x9 OEM Polished RS/SS Wheels Front & Rear
|
|
|
|
|
03-23-2016, 11:29 AM
|
#12 |
|
Account Suspended
Drives: black and silver Join Date: Apr 2014
Location: new york
Posts: 1,728
|
plastic dip works great on them... can is 7 dollars takes about 1 hour to take them out dip and install them... can go wrong with that
|
|
|
|
|
03-23-2016, 11:39 AM
|
#13 |
|
Account Suspended
Drives: 2010 Camaro 1SS LS3 Join Date: Jan 2015
Location: Riverside, CA
Posts: 4,018
|
I left mine in Chrome because of the Camaro side lettering and the chrome part of the bow-tie. But I am considering going gloss black to match my spoiler since I'll be removing the Camaro lettering soon.
|
|
|
|
|
03-23-2016, 12:45 PM
|
#14 | ||
|
Drives: 2012 Camaro SS/RS Join Date: Aug 2013
Location: Exton, PA
Posts: 320
|
Quote:
|
||
|
|
|
|
|
|
|
 |
|
|
