Project Cleaning the Clutter in Our Engine Bay - Page 221 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

krusher · 10-05-2019, 07:23 AM

It is a pain. It is just 4 tabs with metal clips. I knew going in i was never going to re use it so I pried one corner off with a flat screw driver. After that you should have enough room to fit the screw driver in the remaining clips and they just pop off after that. If i rmember right i did have to cut one off for not wanting to come loose

205 · 10-06-2019, 08:16 PM

Thanks. I am still trying to decide if I want to do all that. I may just cut outer top of the plastic. Just enough to give me room. I dunno

205 · 10-09-2019, 07:07 PM

Welp. A little more welding. Then grinding and sanding. I still can't decide if I want to do the filter housing :(

DBHWT · 10-09-2019, 08:46 PM

Kudos...very well done Lots of manhours there.

joshnmn · 10-31-2019, 07:22 AM

Quote:

Originally Posted by krusher

Attachment 1006129

here is my bay all finished

wow!

Top 5 all time favorites. I can't believe the work involved. Great job!

Iron Lung Jimmy · 11-05-2019, 07:29 PM

3000 posts is a bit much to read so I'll ask... did OP ever finish the car?

krusher · 12-08-2019, 07:32 PM

They kind of fell off the face of the earth. They are still on facebook page, but not real active. On this forum they are gone unfortunatley.

*_ERIC_* · 12-09-2019, 12:06 AM

Yea it's sad to not see the final result. I'm guessing those credit card bills came due.

HOU_TX_SS · 02-19-2020, 01:46 PM

Taking longer than expected, but soon enough it will be done! Ok, it's never done, but at least back on the road!

krusher · 02-19-2020, 11:32 PM

Quote:

Originally Posted by HOU_TX_SS

Taking longer than expected, but soon enough it will be done! Ok, it's never done, but at least back on the road!

20200217_174657 (1) by justin sandlin, on Flickr[/IMG]

Wow love the extra sheet metal, makes those wheel wells looks so much better hiding them.

HOU_TX_SS · 02-20-2020, 12:40 PM

Quote:

Originally Posted by krusher

Wow love the extra sheet metal, makes those wheel wells looks so much better hiding them.

Thanks man, took a long time to get them shaped in but worth it in the end.

xc_SS/RS · 02-25-2020, 08:42 AM

Hey is it possible to move only the pcm to the cabin filter area or somewhere else??

krusher · 02-25-2020, 08:45 AM

Sure anything is possible. I have mine just in the cabin air filter area with the ABS brake module welded to the bottom of the cabin filter area.

xc_SS/RS · 02-25-2020, 09:03 AM

Quote:

Originally Posted by krusher

Sure anything is possible. I have mine just in the cabin air filter area with the ABS brake module welded to the bottom of the cabin filter area.

Did you have to lengthen or shorten any wires for the pcm move? Having a bit of trouble finding info about moving only the pcm

12-09-2019, 12:06 AM	#3088
_ERIC_ OMINOUS Drives: '10 Camaro 2SS/RS M6 Join Date: Dec 2012 Location: Lincoln, Nebraska Posts: 223 View My Garage	Yea it's sad to not see the final result. I'm guessing those credit card bills came due. __________________ OMINOUS BUILD

02-19-2020, 01:46 PM	#3089
HOU_TX_SS Drives: Camaro SS Join Date: Jan 2013 Location: Katy, Texas Posts: 156	Figured Id add mine as well. Taking longer than expected, but soon enough it will be done! Ok, it's never done, but at least back on the road! __________________ Fully Built 416ci / Procharger F1X / Century Built 4L80 / ZL1 Differential / Alky Control Meth /Circle D Triple Disk / ID1300s / Fore Innovations Return / Kooks Full Exhaust / Holley HiRam / e85 / 15in Conversion on Forgestar Beadlocks / Tuner: Pat G Last edited by HOU_TX_SS; 02-20-2020 at 12:42 PM.

02-25-2020, 08:42 AM	#3092
xc_SS/RS Drives: 2010 Camaro SS/RS Join Date: Mar 2014 Location: somewhere in MD Posts: 4,883	Hey is it possible to move only the pcm to the cabin filter area or somewhere else?? __________________ 2010 2SS/RS Z/28 intake, NW, FAST 102, speed engineering LT's, some exhaust, ATI -10% pulley, GM flex fuel injectors, DSX flex fuel sensor, MGW shifter, HP Tuners, some suspension work, stickers and a little weight loss. 12.63 @113.53

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Roto-Fab \| Engine Covers - S/C \| Fuse Relay Cover \| Radiator Cover \| Billet Oil Cap+	AutoAgenda	Exterior Parts & Accessories	14	02-06-2013 08:43 PM
New Texas Speed & Performance Engine Machining Center!	Trevor @ Texas Speed	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	18	01-16-2013 03:46 PM
Hawk Performance Brake Pads part HB247Z.575 $85.00	Rogan	USA - Florida	2	10-07-2011 12:10 PM
Acronyms?	KEEP RT	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	20	03-11-2011 08:57 PM
Great Read and Info on Oil Weight	Banshee	Mechanical Maintenance: Break-in / Oil & Fluids / Servicing	1	11-23-2009 09:03 PM

10-05-2019, 07:23 AM	#3081
krusher Drives: 2010 Camaro SS/RS CGM Join Date: Dec 2011 Location: Oskaloosa, IA Posts: 627	It is a pain. It is just 4 tabs with metal clips. I knew going in i was never going to re use it so I pried one corner off with a flat screw driver. After that you should have enough room to fit the screw driver in the remaining clips and they just pop off after that. If i rmember right i did have to cut one off for not wanting to come loose

10-06-2019, 08:16 PM	#3082
205 Drives: 2010 Camaro Join Date: Nov 2018 Location: OK Posts: 161	Thanks. I am still trying to decide if I want to do all that. I may just cut outer top of the plastic. Just enough to give me room. I dunno

10-09-2019, 07:07 PM	#3083
205 Drives: 2010 Camaro Join Date: Nov 2018 Location: OK Posts: 161	Welp. A little more welding. Then grinding and sanding. I still can't decide if I want to do the filter housing :(

10-09-2019, 08:46 PM	#3084
DBHWT Drives: 2013 SS 1LE Join Date: Nov 2011 Location: Cincinnati / N KY area Posts: 559	Kudos...very well done Lots of manhours there.

11-05-2019, 07:29 PM	#3086
Iron Lung Jimmy Drives: Iron Lung, Jimmy Join Date: Jun 2009 Location: Louisiana Posts: 1,449	3000 posts is a bit much to read so I'll ask... did OP ever finish the car?

12-08-2019, 07:32 PM	#3087
krusher Drives: 2010 Camaro SS/RS CGM Join Date: Dec 2011 Location: Oskaloosa, IA Posts: 627	They kind of fell off the face of the earth. They are still on facebook page, but not real active. On this forum they are gone unfortunatley.

02-25-2020, 08:45 AM	#3093
krusher Drives: 2010 Camaro SS/RS CGM Join Date: Dec 2011 Location: Oskaloosa, IA Posts: 627	Sure anything is possible. I have mine just in the cabin air filter area with the ABS brake module welded to the bottom of the cabin filter area.