FS: Edelbrock E-Force w/ ID850's

[Mkn95u0]

Asking $4400 shipped to 48 states. This is just for the blower and injectors only.

I can get updated pictures upon request this is from when it was first installed.

I decided to go all out build and am upgrading everything so no longer need it. there is nothing wrong with the unit at all, very reliable, looks clean & neat under the hood and gives it a 'stock' look.

Auto Trans
My build made these numbers, with these supporting mods, these items are not included with this kit/sale
Made 675rwhp / 629rwtq on 11#'s of boost on E78 w/ supporting mods & cam
Build: E-Force w/ 3.25" pulley (11lbs of boost), 10% OD under pulley, Fore Dual Fuel System, ID850's, AEM CAI, Borla Long Tubes, Flowmaster Super 10's, Circle D 3200 converter 258mm triple disc lockup, cam 226/242 116+4 LSA, ZL-1 Rear end, E85 & BRC Raceworks Tune (previously known as CMS)

ran 10.6 @ 130.19 in 1/4
ran 6.8 @ 103.02 in 1/8th

Blower was installed at 16,957 miles on 12/27/2012
Blower was removed at 43,850 miles on 12/13/2021
This E-force was CARB compliant and has a CARB E.O. number for CA usage

if you have any questions, please feel free to ask.

Edit for additional information:
1) at the $4,400 (shipped/local pickup included) price I will include my ID850's with the blower
2) the kit comes with only the blower, covers, injectors, pulley and a belt that may or may not fit your set up

[Mkn95u0]

or best offer - not in a rush, but i'm not greedy. send me a message if interested.

[Mero562]

Hello. What exactly are you including in this system?

[Mkn95u0]

Originally Posted by Mero562

Hello. What exactly are you including in this system?

Full kit minus injectors and belt - since the belt size will need to be redone on anyone elses build & I did away with the injectors long ago.

The injectors that came with the kit were 54lb injectors, I swapped them out years ago for ID850's.


I'll get a full parts list tomorrow from the shop and post it up.

[Mero562]

Okay. Is there anything else I would need to install it on a 2011 camaro ss automatic? Also where are you located? I live in Southern California too.

[Mkn95u0]

Originally Posted by Mero562

Okay. Is there anything else I would need to install it on a 2011 camaro ss automatic? Also where are you located? I live in Southern California too.

Kit will come with everything needed minus the intercooler & likely belt. At the $4400 price, I will even include my ID850 injectors since I will be upgrading those as well.

The full kit (minus the side covers, which are heat traps that everyone takes off) is located in Hemet at JEP Autoworks (If you were familiar with Cunningham Motorsports, this is the shop that took over the mechanical work and Ryne still tunes for them).

You will need to get it tuned since it has the 3.25" pulley and if you go my ID850 with injectors, you'll get the most out of it with a tune vs the canned tune it came with

edit:
Sorry - yes, it should mount right up to an automatic - mine was auto, but had the afm/dod delete kit, but from what i'm told it should work with either.

[Mero562]

Do you know where I can find a bolt on intercooler? I know they discontinued these kits.

[Mkn95u0]

Originally Posted by Mero562

Do you know where I can find a bolt on intercooler? I know they discontinued these kits.

I replaced mine with Mishimoto, you can check out their website and decide on what size works best for your set up.

[Mkn95u0]

Sale pending w/ back up interest.