Wicker bill on 1LE spoiler? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

damian559 · 10-10-2014, 02:17 AM

Has anybody put the wicker bill on their 1LE? I'm really curious to see what it looks like, I'm too scared to do it first.

Also, does anybody know where I can get the Z/28 carbon fiber heat extractor for my car?

SASQUATCHelvis · 10-10-2014, 07:26 AM

I think the Moreno brothers are working on a CF hood extractor. If you can talk you way into a z/28 part I think they're still around the $2500 mark.

AG1LE · 10-10-2014, 07:28 AM

I've asked the same question about the wicker bill, but no luck so-far

SASQUATCHelvis · 10-10-2014, 08:20 AM

http://www.camaro5.com/forums/showthread.php?t=380517

This guy did it on his ZL1 spoiler, which should be the same or very similar to the '14 spoiler.

AG1LE · 10-10-2014, 08:40 AM

Quote:

Originally Posted by SASQUATCHelvis

http://www.camaro5.com/forums/showthread.php?t=380517

This guy did it on his ZL1 spoiler, which should be the same or very similar to the '14 spoiler.

That's a 2013 ZL1 - not close enough to the 2014-2015 1LE spoiler IMO

White_SS/RS · 10-10-2014, 10:01 AM

I've done a lot of research into this. No I didn't end up doing it but yes it will fit. They curve along the rear of the spoiler is really close to the same and the thickness of the material is the same as well so it will support the use of riv-nuts. You will, depending on how you position it, have holes showing in the raised position and it will hang below in the outer corners when it's down.

Bhobbs · 10-10-2014, 11:12 AM

If you track your car a lot, I would think twice before adding the wickerbill. The 1LE is set up as is to reduce understeer. Al O said adding more downforce to the rear end of the car would cause understeer which is why the 1LE has the spoiler it does.

Spartan01 · 10-27-2014, 09:36 AM

somebody please make a Wickerbill for a 2010 spoiler

JOHNSONROD · 12-09-2014, 11:45 AM

the new JRod Motorsports Aluminum Gurney Lip is a nice piece for a 2010 . havent tested it yet.

tjea · 12-09-2014, 01:07 PM

If you do one end you must do the other end.
Delicate balance between front and rear aero.

JOHNSONROD · 12-09-2014, 01:20 PM

Quote:

Originally Posted by tjea

If you do one end you must do the other end.
Delicate balance between front and rear aero.

Check!

RockerBox · 12-09-2014, 03:31 PM

Chevy sells the carbon hood insert. It's an option when ordering a camaro.

XxScottxXN · 12-09-2014, 03:50 PM

I had my hood insert done with hydrographics and it was a lot nicer paying $100 compared to $2500 for the Chevy one. The weight is almost the same too.

toehead93 · 12-09-2014, 04:05 PM

Does anyone make a 2014+ 1LE splitter extension to go with the wicker bill?

10-10-2014, 02:17 AM	#1
damian559 Drives: 2015 1SS, 1LE, Recaro, NPP Join Date: Apr 2014 Location: Fresno, CA Posts: 927	Wicker bill on 1LE spoiler? Has anybody put the wicker bill on their 1LE? I'm really curious to see what it looks like, I'm too scared to do it first. Also, does anybody know where I can get the Z/28 carbon fiber heat extractor for my car? __________________ 2015 Summit White 1SS, 1LE, Recaros, NPP 498 RWHP 447 RWTQ (Motor) 647 RWHP 723 RWTQ (150 Shot) 12.1 @ 117 (Motor) 11.7 @ 129 (Nitrous) Nitrous Outlet Single Nozzle Kit \| Stand Alone Fuel Cell w/ C16 \| Custom Grind Cam \| Stainless Power 1 7/8 LT Headers \| CAI Intake \| ATI Super Damper \| BMR Trailing Arms & Toe Links \| Prothane Polyurethane Sub-frame Bushings \| JDP Upper Control Arm Bushings \| MT Drag Radials \| Tuned by SS Motorsports Youtube Channel: Click Here

10-10-2014, 10:01 AM	#6
White_SS/RS Drives: 14 1LE Join Date: Mar 2013 Location: Spokane, WA Posts: 1,567	I've done a lot of research into this. No I didn't end up doing it but yes it will fit. They curve along the rear of the spoiler is really close to the same and the thickness of the material is the same as well so it will support the use of riv-nuts. You will, depending on how you position it, have holes showing in the raised position and it will hang below in the outer corners when it's down. __________________ LMS Engineering

10-10-2014, 11:12 AM	#7
Bhobbs Drives: 2015 SS 1LE Red Hot, 1970 Chevelle Join Date: Apr 2012 Location: Chino, CA Posts: 6,989	If you track your car a lot, I would think twice before adding the wickerbill. The 1LE is set up as is to reduce understeer. Al O said adding more downforce to the rear end of the car would cause understeer which is why the 1LE has the spoiler it does. __________________

10-27-2014, 09:36 AM	#8
Spartan01 Drives: Evil Eva, 2010 2SS LS3 Join Date: Aug 2013 Location: Falls Church, Virginia Posts: 3,600	somebody please make a Wickerbill for a 2010 spoiler __________________ "You simply cannot trust quotes found on the internet." -Abraham Lincoln

12-09-2014, 11:45 AM	#9
JOHNSONROD Drives: 62 Chevy & 2021 1SS/1LE manual Join Date: Aug 2010 Location: Kentucky Posts: 893	the new JRod Motorsports Aluminum Gurney Lip is a nice piece for a 2010 . havent tested it yet. Attached Images

10-10-2014, 07:26 AM	#2
SASQUATCHelvis Drives: 2014 Camaro SS 1LE Join Date: Apr 2014 Location: Detroit Posts: 175 View My Garage	I think the Moreno brothers are working on a CF hood extractor. If you can talk you way into a z/28 part I think they're still around the $2500 mark.

10-10-2014, 07:28 AM	#3
AG1LE Drives: '14 1LE Join Date: Nov 2013 Location: NJ Posts: 2,435	I've asked the same question about the wicker bill, but no luck so-far

10-10-2014, 08:20 AM	#4
SASQUATCHelvis Drives: 2014 Camaro SS 1LE Join Date: Apr 2014 Location: Detroit Posts: 175 View My Garage	http://www.camaro5.com/forums/showthread.php?t=380517 This guy did it on his ZL1 spoiler, which should be the same or very similar to the '14 spoiler.

12-09-2014, 01:07 PM	#10
tjea Drives: 2014 1ss 1le Blk/Blk Join Date: Mar 2014 Location: NorCal Posts: 44	If you do one end you must do the other end. Delicate balance between front and rear aero.

12-09-2014, 03:31 PM	#12
RockerBox Drives: 2010 Silverado. Stock height now Join Date: Oct 2014 Location: Springfield Va Posts: 307	Chevy sells the carbon hood insert. It's an option when ordering a camaro.

12-09-2014, 03:50 PM	#13
XxScottxXN Huge Chevy Fan Drives: 14' 2SS/RS 1LE built 4/22/14 Join Date: Apr 2012 Location: Billings, MT Posts: 838	I had my hood insert done with hydrographics and it was a lot nicer paying $100 compared to $2500 for the Chevy one. The weight is almost the same too. Attached Images __________________ 2014 2SS/RS Red Rock Metallic, Recaro seats, sunroof, NPP, Nitto Motivo 275/40/20 front 315/35/20 back, Cold air inductions intake, elite catch can, Stainless Works 1 7/8" long tube headers w/hiflow cats, 20% tint, Intake rod mod by Gwatney Performance, Bo White ported & polished throttle body, powerbond 25% UDP, Howards Cam 226/236 duration- 525/525 lift 110 ....with a WHOLE bunch of fun added!!

12-09-2014, 04:05 PM	#14
toehead93 Drives: 2014 2SS/1LE Join Date: Feb 2007 Location: wpb fl Posts: 3,136 View My Garage	Does anyone make a 2014+ 1LE splitter extension to go with the wicker bill? __________________ Used Racing Brake 2 Peice Rotors for sale: http://www.camaro5.com/forums/showthread.php?t=344754 Summit White 2014 2SS 1LE Recaros, NPP exhaust, Nav 2010 2SS A6 - sold.