07-17-2017, 01:08 PM | #1 |
Drives: 2019 Silverado Z71 6.2L A10 Join Date: Mar 2017
Location: Grapevine
Posts: 2,075
|
ZL1 Rear bumper leaner
My ZL1 emblem leans and I wish I could change it, but now I am getting used to it. I must have had the one eye employee that follows the upper part of the bumper.
How many ZL1's are leaners or not leaners?
__________________
Current ride
2019 Silverado Z71 LTZ 6.2L L87 425hp A10, 4 inch BDS Lift with Fox Factory Race 2.5 Coilovers, Borla Cat back (15HP bump), BFG KM3's 33's. Past Rides 2017 M6 Camaro ZL1 Hyper Blue 2016 M6 GT350 White with blue strips 2014 M6 Mustang GT Premium Track Pack Ruby Red 2012 M6 M3 Melbourne Red Metallic |
07-17-2017, 01:29 PM | #2 |
Drives: 2016 Join Date: May 2017
Location: Northern California
Posts: 314
|
That's weird, those aren't put on by hand.
|
07-17-2017, 04:07 PM | #3 |
ITCRNRS
Drives: 2018 ZL1 1LE Join Date: Jun 2012
Location: Wichita KS
Posts: 1,575
|
I'm planning on removing the rear ZL1 badge shortly after I receive the car, I was never a fan of the 6th gen rear badge placement, always thought it looks kinda like a after thought?
__________________
2018 ZL1 1LE Ordered 6/29/17 Built 11/6/17 Delivered 12/7/17, Summit White, PDR, NAV, https://www.youtube.com/c/tylerpotter
SOLD: 2014 Summit White 1LE 2SS/RS, Recaros, NPP, NAV, KONI Yellow's SOLD: 2012 Black 2LT/RS, Fully 1LE swapped, Brembo swap |
07-17-2017, 04:30 PM | #4 |
Drives: 2013 ZL1 and 2019 Ram Laramie Join Date: May 2017
Location: Milwaukee
Posts: 1,259
|
It looks like it follows the contour of the bend above rather than below.
|
07-17-2017, 08:31 PM | #5 |
Drives: 2017 Camaro ZL1 M6 pdr roof CF blk Join Date: Mar 2017
Location: MA
Posts: 252
|
|
07-18-2017, 01:46 AM | #6 |
Drives: 2017 ZL1 Join Date: Mar 2017
Location: NH
Posts: 278
|
I took mine off the day the car came home, so I'm not sure what angle it was at.
__________________
2017 Camaro ZL1, Nightfall Gray Metallic: M6, PDR, exposed CF, navigation, sunroof
Mods: Rotofab CAI, Tony Mamo TB, Kooks headers (green cats), 18% LPE lower pulley, E85/FlexFuel sensor. BC Forged RS41s (19x10, 19x12)/PS4S, R888R (305/325) Dyno: E40: 661whp/703wtq, 93: 633whp/674wtq |
07-18-2017, 07:29 AM | #7 |
Drives: 2019 Silverado Z71 6.2L A10 Join Date: Mar 2017
Location: Grapevine
Posts: 2,075
|
I have seen them level with the ground too. So no telling what is going on. Now I check every Camaro. I have not seen many ZL1's on the street in the DFW area. I see them at the dealer and check them for level.
__________________
Current ride
2019 Silverado Z71 LTZ 6.2L L87 425hp A10, 4 inch BDS Lift with Fox Factory Race 2.5 Coilovers, Borla Cat back (15HP bump), BFG KM3's 33's. Past Rides 2017 M6 Camaro ZL1 Hyper Blue 2016 M6 GT350 White with blue strips 2014 M6 Mustang GT Premium Track Pack Ruby Red 2012 M6 M3 Melbourne Red Metallic |
01-21-2018, 11:29 AM | #8 |
Drives: Slo'ly Join Date: Dec 2017
Location: Denver
Posts: 138
|
These are just held on with double sided tape? No pins?
|
01-21-2018, 11:32 AM | #9 |
I used to be Dragoneye...
|
|
01-21-2018, 01:15 PM | #10 |
Drives: 2017 Camaro ZL1 A10 Black Join Date: Mar 2017
Location: Florida
Posts: 4
|
The rear emblem on my ZL1 (March 2017 build) is level with the ground.
|
01-21-2018, 04:27 PM | #11 |
|
If that's the case your level is out of whack.
__________________
|
01-21-2018, 07:02 PM | #12 |
Drives: 2018 MBM ZL1 Auto Join Date: Sep 2009
Location: San Juan, Puerto Rico
Posts: 960
|
I think it wolud look better to the right of the Chevy emblem.
__________________
.
|
01-21-2018, 07:05 PM | #13 |
I used to be Dragoneye...
|
So...we asked Al about this when the ZL1 was very first unveiled...and apparently, the designers felt very strongly that the badge up on the deck lid with the bowtie would ruin the balance of the rear of the car since that panel is so small.
The only other place they could put it due to the character lines was down where it is on the main portion of the fascia...and they had to work around the reverse sensors because some of the early, "better looking", placements messed up the sensor readings. The result is what we have in production form. |
01-21-2018, 09:24 PM | #14 |
Drives: 2017 ZL1 Join Date: Mar 2017
Location: NH
Posts: 278
|
Yes, just tape.
__________________
2017 Camaro ZL1, Nightfall Gray Metallic: M6, PDR, exposed CF, navigation, sunroof
Mods: Rotofab CAI, Tony Mamo TB, Kooks headers (green cats), 18% LPE lower pulley, E85/FlexFuel sensor. BC Forged RS41s (19x10, 19x12)/PS4S, R888R (305/325) Dyno: E40: 661whp/703wtq, 93: 633whp/674wtq |
|
|
Post Reply
|
|
|