[Z/284ever]

Originally Posted by Mikes SS

Looks like a mustang not a Camaro has almost identical curves

If that's a Mustang, where's the character line which goes through the door?

[SuperSound]

Originally Posted by Mikes SS

Looks like a mustang not a Camaro has almost identical curves

Threw this together quick. Someone else can point out other differences.

[AceofSpades6]

The teasing makes me want to wait more for something special( camaro).keep up the controlled leaks GM.

[MikeT]

1. It looks okay.
2. Likely little or no improvement over the 5th gen in terms of rear visibility, though.

[PYROLYSIS]

Originally Posted by Number 3

Well considering what he is standing next to.

His comments only show he is clueless.

Data suggests Chevy has the longest lasting trucks BASED ON DATA, and Chevy does quite well in the JD Power Initial (first few months) and Long Term (3 years) AGAIN BASED ON DATA.

As for the NEW Mustang GT350/350R being faster than the 6 year old based Z/28? Well I guess he will just have to wait and see what the new Camaro offers. Me (and most I think) would expect Ford's all brand new to be excellent. And keep in mind the Z/28 is expensive primarily for the engine and brakes. We simply have to wait and see where Chevrolet lands with the new Camaro.

I laugh at completely uneducated comments like his. Base it on data or you only have an opinion..................and his isn't supported by reality.

The pill has had his true identity revealed.

[luckynuts]

Originally Posted by ChefBorOzzy

[GroundhogSS]

The slope at the back edge of the quarter window it completely different.

[enzia35]

Originally Posted by CFTA

check out "JD Babbitt"s comment on Facebook posts about the camaro, cadillac, and the new mustang...

caddy,


https://www.facebook.com/motortrendm...al_comments=83

mustang,


https://www.facebook.com/RoadandTrac...53277830451091

camaro,


https://www.facebook.com/caranddrive...53013793397977

So if he losses his job...good.




Even has his own forum apparently...
http://www.midmichgearheads.com/


I also found that a "Jason D Babbitt" lives in Lansing Michigan, or the town over, Grand Ledge....

He's a neckbeard!!!

[FenwickHockey65]

Some of y'all need vision checks if you really think that resembles a Mustang in the least.

[WHAMMO]

Originally Posted by enzia35

He's a neckbeard!!!

He looks like a total tool!!

V6 calipers with 'Boss' stripes?? Ricer stickers on the side? Name TAG on the top of the window? Fake side air scoop? I'll pass comments on his look..

Unless the guy is a pro drag racer(V6 conversion brakes is not the kind of brakes a pro would run in front..), hes a just a poor kid.

[rtcat600man]

Originally Posted by Number 3

To educate everyone this is not the press. It is one side of what looks to be the pierce die.

The press is the big giant hydraulic thing the dies go into that usually blank, form, re strike and pierce.

This die looks to be in the series were the panel is already formed and additional manufacturing holes are added.

FYI

Very close for die lingo.

Blank dies for a panel like this are not one of the in line dies.

The form die you speak of is known as a draw die.

then depending on how many dies it takes to complete the part, is what comes after the draw die. Typically it would be a trim die, flange die, and finally a pierce die.

What you listed is close enough for all the non die people in the world thou.

[shank0668]

Quarter kind of reminds me of the z06

[AZCamaroFan]

Originally Posted by FenwickHockey65

Some of y'all need vision checks if you really think that resembles a Mustang in the least.

[rtcat600man]

Originally Posted by FenwickHockey65

Some of y'all need vision checks if you really think that resembles a Mustang in the least.

Originally Posted by AZCamaroFan