Homepage Garage Wiki Register Community Calendar Today's Posts Search
#Camaro6
Go Back   CAMARO6 > Search Forums
Reload this Page Search Results


BeckyD @ James Martin Chevy


Page 1 of 17 1 234511 Last »
Showing results 1 to 30 of 500
Search took 0.06 seconds. Search: Posts Made By: Megahurtz
Forum: ZL1 Discussions Today, 03:44 PM
Replies: 15
Views: 260
Posted By Megahurtz
I agree. I've got E50 cars with a 2.3 upper &...

I agree. I've got E50 cars with a 2.3 upper & headers running a drop in filter on the stock airbox pulling draggy times equal or faster than the same setup plus a rotofab. It's just not a restriction...
Forum: ZL1 Discussions Today, 01:11 PM
Replies: 15
Views: 260
Posted By Megahurtz
But no dyno graphs to see if the differences were...

But no dyno graphs to see if the differences were just the normal spikes and dips on a dyno vs actually seeing a gain or loss across the whole range. Either way they are all within the range of dyno...
Forum: ZL1 Discussions 04-29-2024, 08:00 AM
Replies: 11
Views: 554
Posted By Megahurtz
I've never owned an LS or LT motor that didn't...

I've never owned an LS or LT motor that didn't burn about 1/4 - 1/2 quart of oil every 5000 miles or so, regardless of the break in procedure. If you drive the car hard it's going to burn a little...
Forum: Tuning / Diagnostics 04-28-2024, 05:00 PM
Replies: 39
Views: 2,375
Posted By Megahurtz
Yes and yes

Yes and yes
Forum: 2016+ Camaro: 6th Gen Camaro general forum 04-28-2024, 04:51 PM
Replies: 14
Views: 785
Posted By Megahurtz
hptuners.com Buy the mpvi3 and the required...

hptuners.com

Buy the mpvi3 and the required licenses for the CCM which I think is 3 credits. Someone else mentioned that in older cars, the exhaust valve control was in the FPCM, however I've...
Forum: Tuning / Diagnostics 04-27-2024, 03:01 PM
Replies: 39
Views: 2,375
Posted By Megahurtz
Your thoughts about COT pulling SOI back to where...

Your thoughts about COT pulling SOI back to where the exhaust valve is still open are exactly what got me thinking about the theory that it would actually cool the exhaust valve down and even the...
Forum: Forced Induction Discussions 04-27-2024, 08:24 AM
Replies: 10
Views: 336
Posted By Megahurtz
^^ Listen to Joshinator99. He is correct. Don't...

^^ Listen to Joshinator99. He is correct. Don't push the stock LT1 valve train past 6700. It won't survive long at your power level and you'll be rebuilding the engine.
Forum: 2016+ Camaro: 6th Gen Camaro general forum 04-27-2024, 08:15 AM
Replies: 14
Views: 785
Posted By Megahurtz
I do it often with HPTuners. They define the CCM...

I do it often with HPTuners. They define the CCM for most Corvettes and Camaros already.
Forum: 2016+ Camaro: 6th Gen Camaro general forum 04-27-2024, 08:14 AM
Replies: 14
Views: 785
Posted By Megahurtz
Options: #1 HPTuners, tune the CCM and have...

Options:

#1 HPTuners, tune the CCM and have them work any way you want
#2 Get a M2W switch which basically puts the NPP valve fuse on a remote switch that you can open and close whenever you...
Forum: Forced Induction Discussions 04-26-2024, 09:15 AM
Replies: 64
Views: 6,143
Posted By Megahurtz
I understand and appreciate it. I just want one...

I understand and appreciate it. I just want one ASAP lol.
Forum: Forced Induction Discussions 04-26-2024, 06:27 AM
Replies: 64
Views: 6,143
Posted By Megahurtz
SAME

SAME
Forum: 2016+ Camaro: 6th Gen Camaro general forum 04-26-2024, 06:23 AM
Replies: 16
Views: 1,170
Posted By Megahurtz
Don't have sausage hands. Use your sense of...

Don't have sausage hands. Use your sense of touch. Use the right tools.

They are annoying but easy to swap without removing anything, even with the exhaust still in place.
Forum: ZL1 Parts 04-25-2024, 02:11 PM
Replies: 7
Views: 382
Posted By Megahurtz
OK Thanks, I have someone local to you that would...

OK Thanks, I have someone local to you that would pickup and ship to me.
Forum: ZL1 Parts 04-25-2024, 11:21 AM
Replies: 7
Views: 382
Posted By Megahurtz
can you send picture to jason at...

can you send picture to jason at snackbartuning.com ?
Forum: ZL1 Parts 04-24-2024, 08:04 AM
Replies: 7
Views: 382
Posted By Megahurtz
is it the 2.75" or the 3" version?

is it the 2.75" or the 3" version?
Forum: ZL1 Discussions 04-23-2024, 07:58 AM
Replies: 13
Views: 888
Posted By Megahurtz
Just follow GM's OEM logic. 1st gear shifts 300...

Just follow GM's OEM logic. 1st gear shifts 300 RPM early. 2nd gear shifts 100-200 rpm early. 3-4-5-6-7 shift close to redline.

This is how you go the fastest. Don't overthink it.
Forum: ZL1 Discussions 04-22-2024, 10:35 AM
Replies: 10
Views: 614
Posted By Megahurtz
The gains were all within a dyno error % which is...

The gains were all within a dyno error % which is why I wished he showed the dyno graphs as well. Was the power difference a little "peak" somewhere or was the gains carried through the entire range?...
Forum: ZL1 Discussions 04-22-2024, 08:57 AM
Replies: 10
Views: 614
Posted By Megahurtz
I saw it too, but I wish he shard the dyno graphs...

I saw it too, but I wish he shard the dyno graphs so we could see the whole picture.
Forum: Transmissions 04-19-2024, 07:24 AM
Replies: 1
Views: 279
Posted By Megahurtz
no

no
Forum: ZL1 Discussions 04-18-2024, 04:06 PM
Replies: 7
Views: 715
Posted By Megahurtz
Send it to Blackstone Labs and get a report

Send it to Blackstone Labs and get a report
Forum: Tuning / Diagnostics 04-18-2024, 10:25 AM
Replies: 39
Views: 2,375
Posted By Megahurtz
no PID for that, I mean the exhaust valve temp...

no PID for that, I mean the exhaust valve temp being cooled by ethanol evaporation by spraying when the exhaust valve is still partially open. I'm not suggesting this is correct or good or accurate....
Forum: Tuning / Diagnostics 04-18-2024, 07:40 AM
Replies: 39
Views: 2,375
Posted By Megahurtz
I'm not surprised by those results. ...

I'm not surprised by those results.




King isn't wrong for letting SOI start at 378. I am not wrong for suggesting 368. I suspect you will find no discernable difference between the two on the...
Forum: Tuning / Diagnostics 04-17-2024, 11:51 AM
Replies: 39
Views: 2,375
Posted By Megahurtz
If translating to SOI/EOI numbers in the ECU....

If translating to SOI/EOI numbers in the ECU. Basically, that cam card says your Intake Valve opens at roughly 366 SOI and closes at roughly 130 EOI. On the exhaust stroke the exhaust valve is still...
Forum: Tuning / Diagnostics 04-17-2024, 08:17 AM
Replies: 39
Views: 2,375
Posted By Megahurtz
You guys need to remember with DI spraying too...

You guys need to remember with DI spraying too early will just send fuel out of the exhaust valve. The goal is to get as much fuel into the combustion chamber in the spray window. There is no drop in...
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 04-17-2024, 08:08 AM
Replies: 8
Views: 746
Posted By Megahurtz
If you have a GOOD set of tools, have experience...

If you have a GOOD set of tools, have experience working on cars, can get the car high enough in the air, and have an entire weekend of patience, then you can get it done yourself.

If you have...
Forum: Tuning / Diagnostics 04-16-2024, 05:33 AM
Replies: 17
Views: 813
Posted By Megahurtz
Yes

Yes
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 04-16-2024, 05:32 AM
Replies: 14
Views: 901
Posted By Megahurtz
Nothing alarming about that quote.

Nothing alarming about that quote.
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 04-16-2024, 05:30 AM
Replies: 8
Views: 746
Posted By Megahurtz
1. MSD wires are great and fit better than...

1. MSD wires are great and fit better than factory with headers. We always recommend MSD's with headers. Anytime we have a client with headers develop a random misfire, its a stock plug wire for...
Forum: Tuning / Diagnostics 04-11-2024, 04:16 PM
Replies: 39
Views: 2,375
Posted By Megahurtz
The pulse width change is likely due to weather...

The pulse width change is likely due to weather variances or airflow variances. SOI and EOI are just the start and stop of the injection event. The duration of the event is determined by the airmass...
Forum: ZL1 Discussions 04-11-2024, 10:26 AM
Replies: 14
Views: 881
Posted By Megahurtz
you should log SOI and EOI as well

you should log SOI and EOI as well
Showing results 1 to 30 of 500
Page 1 of 17 1 234511 Last »

 
Forum Jump

All times are GMT -5. The time now is 10:29 PM.

Contact Us - CAMARO6 - Archive - Privacy Statement - Terms of Service / DMCA Policy - Top

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.